I'm in need of a wiper motor for a 63 SDV. Mines toast, stopped at 90 degrees on the windshield, now blows fuse whenever power applied.

tbbahner@aol.com

Thanks

Facebook Facebook

Views: 291

Reply to This

Replies to This Discussion

Parts Geek got one $ 205    exchange , free shipping

Tom, do you have the shop manual? It  has troubleshooting steps to identify the problem. Since it's blowing fuses its\'s either shorting to ground or just drawing too much load. My best guess would be to check the motor brushes, these cars are so old now,they may be worn out .Disassembly of this motor looks pretty involved though.. My parts car still has it mounted ,don't know how good it would be .

Good point on the brushes.  I would recommend just having it professionally repaired. The piece will look and perform as new.  This is a common GM wiper motor, so it is not a difficult motor to rebuild or repair. Just google windshield wiper motor repair.

Thanks all for the comments. I found one off a 64 on epay I'll try. Jason, you can take my name off you list for now.

While I've got this disassembled, I'm replacing all the washer hoses. Also looking to see if there's anything I can do to clean up the joints on the wiper linkage to reduce drag. Doesn't look like I can do much with it and still keep it dry(without lube). Any suggestions on this???

Remove the wiper transmissions and clean up the pivot heads that rotate.  Use a penetrating oil to get the crud loosened up, and flush out with brake parts cleaner.

Removing the transmission can be time consuming, especially if you run in to issues getting any of those 9 Phillips Screws out that hold it in place. I would visually inspect, and unless you see major rusting, with the cowl chrome grills removed, hit the transmission assembly with compressed air and spray the pivot points with WD40 and work back and forth and you should be good to go for many years.  If you have heavy rust and decay on the transmission assembly (which I have only seen occasionally) I have over a dozen excellent complete transmission assemblies for $50 each + s/h.

Hey all, thought I'd follow up on this thread.

 Received  the wiper motor off Epay and got it  installed. We be "wipin" again!

Took the cowl grill assembly off and cleaned up all the joints on the transmission. Has much less drag than it did before. Still no washer but that's one of those things I'm not too worried about.

Thanks again to all for the assistance.

Tom B

Congrats! Yep, wiper is the main thing, You can pick at the washer as time permits. I had my car 15 years without a working washer and finally bought a repair kit and TCB'd it and sure felt good to see it work.

RSS

Photos

  • Add Photos
  • View All

Forum

Logans Intake Project, 1964 Fleetwood, Progress Report #3

Started by Logan Robb in 1963/64 Cadillac Specific Discussion. Last reply by Jason Edge 10 hours ago. 2 Replies

Not much of an Update and Questions: I was inspecting the top end and had removed the air cleaner in preparation to replace the intake. It was dirty so decided it needed a wipe down. My goof was…Continue

headlight / dimmer switch confusion (63 Sedan Deville)

Started by Bill Wolf in 1963/64 Cadillac Specific Discussion. Last reply by Bill Wolf 12 hours ago. 4 Replies

The schematics are from the repair manual and show a LIGHT BLUE wire coming from the headlight switch to the dimmer switch. From the dimmer switch to the low beams on a TAN wire and to the high beams…Continue

Replacement Front Crankshaft Seal - 1964 Eldorado (429ci)

Started by Michael Stinson in 1963/64 Cadillac Specific Discussion. Last reply by Jason Edge 23 hours ago. 2 Replies

My mechanic is having difficulty sourcing a front crankshaft seal.  Can anyone recommend a replacement front crankshaft seal, and where to purchase?  Amazon has a few that I think(?) are replacements…Continue

Tags: Seal, Crankshaft, Front

Original Rim Color

Started by Logan Robb in 1963/64 Cadillac Specific Discussion. Last reply by Michael Stinson yesterday. 3 Replies

When I get some new shoes for my 64 Fleetwood, I'd like to recondition the rims. I'd thought of getting them powder coated, and still plan to eventually, but the $700 quote I received shunted that…Continue

Blog Posts

Edelbrock Carb Block off Plates

Posted by Chase on March 12, 2025 at 2:05pm 14 Comments

Hey guys,

I have installed the same Edelbrock carb and have done everything the same as Jason’s carb and intake project. In the spring and summer months the car starts, runs and idles great! In the fall and winter months on a cold start, the car starts awful and wants to die until it warms up. I have to keep my foot on the throttle until it warms up or it will idle just terrible and try to die. Once it’s warm, it runs fantastic! Whats going on here? I was thinking of removing the…

Continue

'63 Tailfin Tales

Posted by Mark Mata on February 22, 2025 at 5:00pm 9 Comments

New old stock seat material

Posted by Ray Schick on August 22, 2024 at 6:25pm 2 Comments

I bought this seat material thinking that it’s…

Continue

Loud air moving sound within carb with cleaner removed

Posted by Dave Fehrle on March 23, 2024 at 3:23pm 8 Comments

While checking my Carter carb with engine running, I took the air cleaner off and there was a very loud hissing sound of air. I placed a piece of paper over the carb and it didn’t move up or down, is this normal?

Videos

  • Add Videos
  • View All

© 2025   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service