Greetings Everyone.  I read a discussion thread about "radiator and related", covering coolant overflow.  Has anyone fitted an overflow reservoir / bottle to their 64 Cadillac?  Is there if a particular universal reservoir that can be fitted and attached to the radiator support housing or the passenger inner fender?  Then insert the overflow tube into the reservoir?   Thoughts / suggestions? 

I am monitoring coolant overflow and / or possible mixing with the oil.  If an overflow reservoir doesn't clear up the puddle on the garage floor, I will investigate a possible head gasket issue.  

Facebook Facebook

Views: 69

Reply to This

Replies to This Discussion

Several folks run the generic square coolant overflow tank. I see this in 99% of the uses. Amazon.com: Dorman 54002 Engine Coolant Recovery Kit Universal Fit ...

I mount mine on the RF inner fender right behind the radiator core support. 

Thanks Russ.  I'll check out the one you recommend. 

Hi Michael,

    I have a 64 Series 62 and albeit it never had an overflow for coolant, I decided to install one for safe measure.  I found one that fit perfectly between the grill and the metal frame.  Only had to drill one hole (the other was there) and it works perfectly.  My email is ddibari56@gmail.com and can give you a picture and details.

Dennis DiBari, Cottekill NY

Michael,

I sent you an email with the information you requested.

Dennis DiBari

I saw somebody do this a few years back. Thought it was a clever solution

Hi Mike,

     Any luck with the coolant overflow tank we talked about for your Caddy?

Dennis DiBari

RSS

Photos

  • Add Photos
  • View All

Forum

Front door handle lights not working

Started by Bill Wolf in 1963/64 Cadillac Specific Discussion. Last reply by Kurt yesterday. 1 Reply

My front door handle lights would not go on when I opened the doors. Bulbs were good and had power to them. Was not getting a ground. The door switch was corroded and wasn't making contact when the…Continue

lighted headlight switch

Started by Bill Wolf in 1963/64 Cadillac Specific Discussion. Last reply by Bill Wolf on Saturday. 2 Replies

I had to replace the heater core in my 63 SDV, so I decided to replace all the dash lights with LED's. and replaced all the vacuum lines. While I was in there, I added a light to the headlight switch…Continue

Rear suspension project

Started by Dave Fehrle in 1963/64 Cadillac Specific Discussion. Last reply by Robert Alan Shannon May 13. 9 Replies

I’m starting the complete rear suspension update/upgrade-new springs and shocks,replacing spherical joint and bushings on yoke and control links! Just wondering if there are any tips to help with the…Continue

TV rod adjustment 1963 Cad

Started by Mark Geertsma in 1963/64 Cadillac Specific Discussion. Last reply by Russ Austin May 12. 4 Replies

I’m struggling with my TV rod adjustment. I’ve been trying to adjust it as per shop manual, but it’s still not OK. When cold, it shifts smoothly through all four gears, when hot, it hesitates (lots…Continue

Tags: adjustment, rod, TV

Blog Posts

Edelbrock Carb Block off Plates

Posted by Chase on March 12, 2025 at 2:05pm 14 Comments

Hey guys,

I have installed the same Edelbrock carb and have done everything the same as Jason’s carb and intake project. In the spring and summer months the car starts, runs and idles great! In the fall and winter months on a cold start, the car starts awful and wants to die until it warms up. I have to keep my foot on the throttle until it warms up or it will idle just terrible and try to die. Once it’s warm, it runs fantastic! Whats going on here? I was thinking of removing the…

Continue

'63 Tailfin Tales

Posted by Mark Mata on February 22, 2025 at 5:00pm 9 Comments

New old stock seat material

Posted by Ray Schick on August 22, 2024 at 6:25pm 2 Comments

I bought this seat material thinking that it’s…

Continue

Loud air moving sound within carb with cleaner removed

Posted by Dave Fehrle on March 23, 2024 at 3:23pm 8 Comments

While checking my Carter carb with engine running, I took the air cleaner off and there was a very loud hissing sound of air. I placed a piece of paper over the carb and it didn’t move up or down, is this normal?

Videos

  • Add Videos
  • View All

© 2025   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service