63/64 Cadillac Website

Dino Wiper Swap

Yesterday I finally pulled my already very nice windshield wiper motor and washer pump assembly in my 64 Coupe de Ville 'Dino', to replace with a rebuilt unit I have had a couple of years and recorded a quick video before removing. Here is that video clip testing the one I removed, then a picture of the rebuilt one installed. Both were very nice motor/washer pump assembles. The old one went shipped out to a Chapter Member today.

0 members like this

Facebook Facebook

▶ Reply to This

Replies to This Discussion

Permalink Reply by Logan Robb on March 12, 2023 at 11:08pm

Great video. Wondering if you could post a pic of the actual nozzles on the cowl? This is a future project on my 64 Fltwd and would like to come back to this thread.

▶ Reply

Permalink Reply by Jason Edge on March 13, 2023 at 4:38am

Logan, Are yours missing? If so, I have plenty of the washer jet and nozzles as seen below for $10 each side. Email me at jasonedge64@outlook.com.

▶ Reply

Permalink Reply by Logan Robb on March 13, 2023 at 9:23am

Based off of the photo, I suppose mine are not missing. I thought there to be some piece that connects to the end of the jet there. With the eye, it looks like it would shoot off to the side, not onto the w/s.

-Logan

▶ Reply

RSS

Welcome to
63/64 Cadillac Website

Sign Up
or Sign In

Or sign in with:

Photos

Forum

Bleeding brakes

Started by Dave Fehrle in 1963/64 Cadillac Specific Discussion. Last reply by Russ Austin 17 hours ago. 3 Replies 0 Likes

I have finished replacing all the rear suspension and am at the last item, which is bleeding the rear brakes. I am using the Jason Edge vacuum pump method and all went well with the rear passenger…Continue

Front grill

Started by Phillip Hill in 1963/64 Cadillac Specific Discussion. Last reply by Dennis P. DiBari yesterday. 8 Replies 0 Likes

Hi everyone im currently restoring my my front grill due to some previous clown painting it with silver frost paint and doing a dodgy job I would like to know what parts of the grill are anodised.it…Continue

Getting hot when going fast…

Started by Mack in 1963/64 Cadillac Specific Discussion. Last reply by Dennis P. DiBari on Tuesday. 6 Replies 0 Likes

So… I do have a few of 63 Coupes, all have same setup with carbs, Pertronix, shroud, new US Radiator radiators etc … but only one of them gets a bit hot when I am hauling faster than 60mph and car…Continue

Rainstorm out of nowhere!

Started by Logan Robb in 1963/64 Cadillac Specific Discussion. Last reply by Dennis P. DiBari on Monday. 1 Reply 0 Likes

After dinner last night, we went for a quick cruise as the weather was cooler and the sun set was looking really good!Out of nowhere, a pop up shower appeared overhead and down-poured as we were…Continue

Blog Posts

1963 RHS A/C kick panel - photos needed

Posted by SK on June 2, 2025 at 2:20pm 2 Comments 0 Likes

Could someone post front and back photos of the 1963 right-hand kick panel with A/C?

My car didn’t come with the original kick panels, so it's a bit of a mystery to me how I should cut the backing board and carpet to fit around the A/C.

Many thanks,

-Samu

Edelbrock Carb Block off Plates

Posted by Chase on March 12, 2025 at 2:05pm 14 Comments 1 Like

Hey guys,

I have installed the same Edelbrock carb and have done everything the same as Jason’s carb and intake project. In the spring and summer months the car starts, runs and idles great! In the fall and winter months on a cold start, the car starts awful and wants to die until it warms up. I have to keep my foot on the throttle until it warms up or it will idle just terrible and try to die. Once it’s warm, it runs fantastic! Whats going on here? I was thinking of removing the…

Continue