We had an excellent tech tip in the January 2015 newsletter by Ron Perry regarding adding new seals to fender skirts. It was also posted as a separate Help topic article at this link  Fender Skirt Seal Replacement by Ron Perry

Just to update this a bit, my friend and chapter member George Karageorge came over with some 3M 08475 3/8" x 30' Seam Sealer Tape that seems like a great alternative seal material that already had the adhesive on one side.

I was concerned about the thickness and measured an original fender skirt seal at 3/64".  I then measured the 3M Seam Sealer Tape and it is also exactly 3/64".  The 3/8" width is a bit wider than the skirt lip so you can either trim off the excess or lip it around. We lipped a bit around my fender skirt and it seems to hold very tight.  Amazon has a limited supply, but there are other sources for this 3M tape.
Just as a reminder, the fender skirt seals provide insulation against rattling and pushed the skirt out even with the rest of the body of the car, so this is a good upgrade.  If interested in the 3M tape at Amazon click on 3M 08475 3/8" x 30' Seam Sealer Tape.    Thanks, George!

Facebook Facebook

Views: 739

Reply to This

Replies to This Discussion

You're welcome.  I got mine at Carolina Auto Paint off Germantown Rd/Daimler Way.  They have been pretty helpful, mixed a perfect light gray single stage for repainting my ashtrays.glove lid etc

Have been trying to get hold of the tape. Contacted 3M here in Sweden but they didn't have it!

Did however find the perfect solution as I did remember I had a roll of teflon insulation tape, for chemical tankers lying about. Who doesn't?

The skirt is now perfectly flush and free of any resonans. I am very pleased with the outcome. Unfortunately there is not any marking on the roll of teflon tape. So can't tell you of maker or model. As this product is produced to withstand any chemical I guess it will keep a good seal and last forever.

RSS

Photos

  • Add Photos
  • View All

Forum

Dino Diaries - July 11, 2025 - Busted!

Started by Jason Edge in General Discussion. Last reply by Jason Edge 13 hours ago. 4 Replies

So I am starting to crawl around under Dino seeing what I can fix or upgrade and as I was putting the trans linkage in a few nights ago, the rear trans mount caught my eye. I remembered that these 64…Continue

Bleeding brakes

Started by Dave Fehrle in 1963/64 Cadillac Specific Discussion. Last reply by Russ Austin on Thursday. 3 Replies

I have finished replacing all the rear suspension and am at the last item, which is bleeding the rear brakes. I am using the Jason Edge vacuum pump method and all went well with the rear passenger…Continue

Front grill

Started by Phillip Hill in 1963/64 Cadillac Specific Discussion. Last reply by Dennis P. DiBari on Wednesday. 8 Replies

Hi everyone im currently restoring my my front grill due to some previous clown painting it with silver frost paint and doing a dodgy job I would like to know what parts of the grill are anodised.it…Continue

Getting hot when going fast…

Started by Mack in 1963/64 Cadillac Specific Discussion. Last reply by Dennis P. DiBari on Tuesday. 6 Replies

So… I do have a few of 63 Coupes, all have same setup with carbs, Pertronix, shroud, new US Radiator radiators etc … but only one of them gets a bit hot when I am hauling faster than 60mph and car…Continue

Blog Posts

1963 RHS A/C kick panel - photos needed

Posted by SK on June 2, 2025 at 2:20pm 2 Comments

Could someone post front and back photos of the 1963 right-hand kick panel with A/C?

My car didn’t come with the original kick panels, so it's a bit of a mystery to me how I should cut the backing board and carpet to fit around the A/C.

Many thanks,

-Samu

Edelbrock Carb Block off Plates

Posted by Chase on March 12, 2025 at 2:05pm 14 Comments

Hey guys,

I have installed the same Edelbrock carb and have done everything the same as Jason’s carb and intake project. In the spring and summer months the car starts, runs and idles great! In the fall and winter months on a cold start, the car starts awful and wants to die until it warms up. I have to keep my foot on the throttle until it warms up or it will idle just terrible and try to die. Once it’s warm, it runs fantastic! Whats going on here? I was thinking of removing the…

Continue

'63 Tailfin Tales

Posted by Mark Mata on February 22, 2025 at 5:00pm 9 Comments

New old stock seat material

Posted by Ray Schick on August 22, 2024 at 6:25pm 2 Comments

I bought this seat material thinking that it’s…

Continue

Videos

  • Add Videos
  • View All

© 2025   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service