How do I fix this (without inadvertently setting the car on fire)?


Views: 143

Reply to This

Replies to This Discussion

Michael, this insulation was installed upside down. That is the backing tearing off & hanging down. You will have to remove it all, clean the mounting surface and install new insulation with the fabric side glued to the hood. Some cars (like my 76 Seville) have the fabric side down but it is attached with clips, not glue.


Thanks for the post.  Do you know where I can get the insulation and proper adhesive?


If you Google "1964 Cadillac hood insulation" several suppliers pop up. I bought mine so long ago, I don't remember where I got it. You will also find several discussions online as to which side goes down. I remember researching that before installing mine. Actually on the original insulation, neither side had a fabric backing. I used contact cement to attach mine.The fabric backing offers a more uniform surface for the glue to adhere to.

I’ll look it up today.

I have a cruise event tonight.  Do you think it will be a problem to duct tape the insulation up until I get the new insulation?   I’m concerned about the current falling insulation getting caught up in the belts, and removing it my result in excessive heat on the hood metal and damage the new paint.  Thoughts?

You can duct tape it in the meantime. I understand your concern about your new paint. Personally I drove my car for years with no hood insulation, even after I got my car painted and the heat was not excessive enough to damage the paint. I think the insulation is mainly for sound deadening as I've seen many cars with no hood insulation from the factory. The diesel Cadillacs from the 80's had extra hood insulation to muffle that clattering Olds diesel (a sound which I actually like : ) 

No problem at all regarding the paint with the hood sound insulation removed

I have no hood insulation for many years —-  all good 

Understand your concern with the brand new paint job - but you will be just fine 


Do enjoy your cruise event

You should be a big hit with that fine ride 


I would remove any hanging hood insulation until you have the chance to replace it as not sure how well the duct tape will stay bonded with the engine heat

You will be fine with it off 

Just my 2 cents 



Thank you for all your advice.  I ended up simply pulling off the insulation that was hanging down and went to the cruise. Had a great time!

Ordered new insulation from Caddy Daddy And will install it when it arrives.

Problem solved!


Today I removed the hanging hood insulation, cleaned the contact surfaces, and installed the new insulation.  Looks pretty good.  Thanks again for the all the advice.  By the way, I don’t know why the photo keeps turning. ;-)



  • Add Photos
  • View All


differential seal

Started by Al zink in 1963/64 Cadillac Specific Discussion. Last reply by Jason Edge 51 minutes ago. 1 Reply

Can anyone provide me with a good source for a differential seal for my 63 cadillacThanksContinue


Started by Mark Bartlett in 1963/64 Cadillac Specific Discussion. Last reply by Mark Bartlett 6 hours ago. 26 Replies

Hi I am new to this Discussion  I currently purchasing a 64 Deville convertible and It has bias ply tires that are 15 year old  they have L-78-15 tires and would like to put on radials . Question …Continue

The amazing Th-400 trans still going strong in 2023 in drag racing circles

Started by Tony and Ginny 429 in 1963/64 Cadillac Specific Discussion 8 hours ago. 0 Replies

I just read an article about a drag race engine producing 2500 plus  HP using a TH-400 trans behind it Sure the trans was modified some to handle that kind of power but was still a big ( good )…Continue

Tags: trans, TH-400, The

Transmisson Rebuild Time?

Started by Logan Robb in General Discussion. Last reply by Tony and Ginny 429 8 hours ago. 6 Replies

I've posted about this issue in the past and I thought I had it resolved. It would appear I do not as it has reared its ugly head again. My TH400 in the 64 Fleetwood has an intermittent problem of…Continue

Blog Posts

Lower Front End Ball Joints

Posted by Logan Robb on May 11, 2023 at 9:04am 7 Comments

Good Morning all! 

I took the 64 into the shop to have some adjustments completed and in the process decided to have the lower ball joints replaced as was recommended the last time I had it in. I ordered the parts and came into the shop. They quoted me nearly $500 to replace those lower ball joints requiring nearly 4hrs of labor. Now this is a reputable shop and they know me by name here and they will continue to get my business. I am just questioning what on earth is…


1964 power steering sector rebuild

Posted by CHRIS CARLSON on March 20, 2023 at 11:32pm 3 Comments

 I'm having my steering sector rebuilt, and considering changing it from 20-1 ratio 4.2 turns lock to lock to 3.5 turns lock to lock @ 16-1 ratio, If i change from a 3 1/4" box to a 3" box i could have a 14-1 Ratio steering response would be faster, shorter distance to turn the wheel to get a response,   has anyone done this? and how do you like it? thank you

1964 Daville dashboard clock

Posted by Willem Bol on March 13, 2023 at 11:33am 2 Comments


Can somebody help me finding a dashboard clock  for my 1964 Cadillac DeVille Convertible?

Thank you in advance,

Willem Bol

The Netherlands

Does anyone know where I can get the bushings for AC compressor mount on the 429?

Posted by Robert Schles on February 21, 2023 at 11:45am 2 Comments

I've looked at the usual rubber sources but couldn't find any. 


  • Add Videos
  • View All

© 2023   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service