I have 3 work shelves with countertops flanking the side and back wall on my garage, and a large work bench, and the countertops have always been gloss white but have decided to go with the Cadillac Engine Blue. I guess the fire hydrant I just painted inspired me. Just finished part of my back wall counter.... so I have a looong way to go. I had Home Depot scan a part I had painted with Bill Hirsch Cadillac Blue and think they got it pretty close.
Tags:
Jason that looks like newer joists and plywood floors sitting on your old foundation. Was there some major renovations at some point?
Clovis, I am going to go through and reinforce the entire house foundation. I started on the back room, now our living room around July last year. All floor joists are being double sister-boarded, sandwiched between 2 new 2" x 12"s. I am tying it all together with 2" x 12" end caps and 16 gauge angle iron brackets. 5/16, 3/8, and 7/16" SPAX Power Lag HDR screws are being used to hold it all together. There is of course PL Premium Construction Glue applied. I started on this back room because we want to build off of it in the near future and put in a downstairs bathroom and bedroom access to this area is easiest from the location where the new room is going on. There is also some settling away from the chimney bases... not much in this room... but will push it up a tad before we build off of it.
For this room I used 20 12" x 16" x 16 foot beams, and 18 12" x 16" x 12 foot beams. Needs to say those 16' 2x12's are heavy and took a few to figure out how to install my self. So that is the new board. You see plywood overhead in the one section because in 1912, that back section was a kitchen, pantry, and open porch. When I bought the house in 1996, I made it one big open room with a cathedral ceiling and enclosed the porch to make part of the room. Since porches have a slope the old porch was torn out and refloored. That is of course a very quick, crude summary. Chimney's were taken out, pipes were re-routed, a drop ceiling was removed, an attic was removed, all walls and ceilings were wired, insulated and 1/2" ply wood was put in to replace the lath and plaster. On the front wall in order to be able to embed the 4" drain pipe I actually double layered the 1/2" plywood so it has 1' of solid plywood.
In addition to reinforcing the floor joists and beams, I completely rewired and have now replumbed under that room. There was a maze of old and new plumbing and wiring under this section since it had been a kitchen. There was copper, cast iron, PB, CPVC, PVC, in terms of plumbing which as all been replaced with 3/4" PEX for supply, and PVC for drain. Older LAN Ethernet was replaced with Cat 7, and cable was replaced. All electrical wiring was redone and separate circuits were installed for GFCI crawlspace outlets, and LED Strip Lights. So wiring, cable, plumbing and foundation reinforcement were all addressed.
This is of course just one of many project in our house. I have a dozen more "interesting" projects. When we bought the house in 1996 I was pre-digital camera and have yet to scan the hundreds of pics we took early on. there is one of me standing on the chimney that went up through the middle of this room handing my mom a brick to chunk out the side window. Those bricks were in turn used to build a deck by our old cook house...yet another major project.
The Bigger project I undertook last year was the BIG DIG. I Only had about 1 to 2 feet of height from ground to floor joist which meant I basically had to work on my back slithering around like a snake. I told myself when I retire I was going to dig it out so I would have room to work. My goal has been to dig it out now at age 53, so I can sit on my butt at age 63, 73 and 83 and work with my power tools! So far I have dug out about 3/4's under the entire house. I calculated it a while back at about 100 cubic yards.. not feet... but yards of dirt. I expect to finish in 2 to 3 months and other projects will go much faster. To see more on that project and see where this room's crawlspace started Click Here.
Anyway, here are a few "post-digital" pics of what was going on above the living room floor in recent years.
Nah, I had on 2 t-shirts, a work shirt and a flannelette shirt and shorts.
Hey Jason, its a real early girl, Nov. 1960 build date and # 7069 off the assembly line.
They were only released here on Sept. 11 1960.
Now that's a crawl space! Mine is maybe 18" under the floor joists and a dirt floor that is reminiscent of the surface of the moon. I take pride in doing as much as possible when it comes to home repairs and improvements but the older I get, the more I deplore the thought of even getting under the house.
I use to hate getting under there but I had to do a lot of fast work underneath when we first bought the house. A kitchen was moved to what was a bedroom to make way for a living room, and the entire down stairs wiring was redone with grounded Romex wiring, and much more. On the plumbing I tapped into what was there and T'd off and routed to the new kitchen area. Having 4 feet of height and a nice flat clean surface to work on via the tempered hardboard and plenty of lighting makes work under there a breeze. I actually now work in this area in my regular clothes and socks! LOL By the time I am 60 (7 years from now) I would like to have the entire underbelly of the house like this!
Looks great Jason. I must say we are a lot alike, we both have more crap than carters got pills (as my mother used to say LOL)
I had to do some plumbing under the new cottage I bought. It's on a piered foundation and literally is 12 inches off the ground. The previous owner had used a water sprinkler T in the supply line and it cracked at the furthest point from the entrance to the crawl space. I was changing from black plastic to pex from the pump to just under the cottage and pulled a bit of the old stuff out and broke that T. Needless to say it flooded quire a bit and all the ants came out of the ground, ALL OF THEM. Ants dont like to be layed on and squished LOL. Plus being surrounded by water there were a bazillion spiders living under there also. NOT FUN!!!. My solution is that I'm going to raise the whole cottage 1.5 to 2 feet and install a proper friction piling foundation under it. It cant be dug out as water would just sit under it and pool. The water level of the lake is only 2.5 feet lower than land right now. The piling will be 12 to 14 foot 1/4" X 8" pipe and installed with a 100 pound jackhammer standing on top of a ten foot ladder. Then the cottage is jacked up above the pipes and 10" I beans are pulled underneath and welded to the pipes then I will lower the cottage back to it's new foundation.
Sounds like a fun project. I don't have to worry about the hitting the water level, but once entire foundation is reinforced wouldn't mind pushing the house up about 1 foot. Since our water table is about 30 to 35 feet down and we are relatively at the top of our road it is easier to go down to get height underneath.
Oh mate, save all that work until we are there next year, I'll give a hand with it.
Dont worry Kevin there is always work at the islands. And fishing and sunbathing and swimming and boating well you get the point.
Started by Bobby Brown in General Discussion. Last reply by Dennis P. DiBari 6 hours ago. 1 Reply 0 Likes
My reservoir is a little low. Any recommendations on my purchase of refill fluid? There are likely new fluids and I’d like to buy the right product. Thanks. Continue
Started by Jason Edge in General Discussion. Last reply by Jason Edge yesterday. 4 Replies 0 Likes
So I am starting to crawl around under Dino seeing what I can fix or upgrade and as I was putting the trans linkage in a few nights ago, the rear trans mount caught my eye. I remembered that these 64…Continue
Started by Dave Fehrle in 1963/64 Cadillac Specific Discussion. Last reply by Russ Austin on Thursday. 3 Replies 0 Likes
I have finished replacing all the rear suspension and am at the last item, which is bleeding the rear brakes. I am using the Jason Edge vacuum pump method and all went well with the rear passenger…Continue
Started by Phillip Hill in 1963/64 Cadillac Specific Discussion. Last reply by Dennis P. DiBari on Wednesday. 8 Replies 0 Likes
Hi everyone im currently restoring my my front grill due to some previous clown painting it with silver frost paint and doing a dodgy job I would like to know what parts of the grill are anodised.it…Continue
Posted by SK on June 2, 2025 at 2:20pm 2 Comments 0 Likes
Could someone post front and back photos of the 1963 right-hand kick panel with A/C?
My car didn’t come with the original kick panels, so it's a bit of a mystery to me how I should cut the backing board and carpet to fit around the A/C.
Many thanks,
-Samu
Posted by Chase on March 12, 2025 at 2:05pm 14 Comments 1 Like
Hey guys,
I have installed the same Edelbrock carb and have done everything the same as Jason’s carb and intake project. In the spring and summer months the car starts, runs and idles great! In the fall and winter months on a cold start, the car starts awful and wants to die until it warms up. I have to keep my foot on the throttle until it warms up or it will idle just terrible and try to die. Once it’s warm, it runs fantastic! Whats going on here? I was thinking of removing the…
ContinuePosted by Ray Schick on August 22, 2024 at 6:25pm 2 Comments 0 Likes
I bought this seat material thinking that it’s…
July 20, 2025 from 8pm to 9:30pm – Zoom
0 Comments 0 Likes
© 2025 Created by Jason Edge.
Powered by