63/64 Cadillac Website

I am a very lucky Man!

I have to say that I am a very lucky man! I showed my wife, Cheryl Edge my batch of re-chromed parts for my 1964 Cadillac Coupe DeVille, and knowing that I had just shelled out over $1000 for the chrome plating for the parts seen in the included picture, she turned to me and instead of complaining about the money spent, she pointed to the stainless steel side trim molding and asked " Can you also have that rechromed." Life is good... it is very, very good!

2 members like this

Facebook Facebook

▶ Reply to This

Replies to This Discussion

Permalink Reply by 0ycv56nn7r5pc on January 27, 2016 at 10:16pm

Jason

Yes you are!

She sounds like a real keeper!!

▶ Reply

Permalink Reply by Jason Edge on January 28, 2016 at 8:00am

Thanks guys. I have been asked who did the plating. The plating was done by Atlantic Coast Plating out of Athens, TN. Here is there website: http://www.atlanticcoastplatinginc.com/

For larger bumper ends I use Tri-City Plating out of Elizabethton, TN. Here is their website http://www.tricityplating.com/

I highly recommend both and will read more about both in upcoming newsletters.

▶ Reply

Permalink Reply by 1e62mxg5u3b01 on January 28, 2016 at 9:01am

That is an awesome story! Can't wait to get my stuff back and begin reassembly.

▶ Reply

RSS

Welcome to
63/64 Cadillac Website

Sign Up
or Sign In

Or sign in with:

Photos

Forum

where to find 1963 Cadillac Plastic Door Pin Anchors

Started by Frank Murch in 1963/64 Cadillac Specific Discussion. Last reply by Jason Edge 15 hours ago. 2 Replies 0 Likes

Hi allwhere can I find these - 1963 Cadillac Plastic Door Pin Anchors. Mine are from1963 and a little tiredThanksContinue

Rear Main Seal Oil Leak Fix with Bearing Cap Modification

Started by Kurt in 1963/64 Cadillac Specific Discussion. Last reply by Matti Roth yesterday. 15 Replies 4 Likes

Many owners have reported oil leaks at the rear main seal even after replacing the seal, myself included. Recently Tony Lentini found a Serviceman bulletin published in February 1965 which details a…Continue

Future of CLC Judging

Started by Jason Edge in Restoration Discussion. Last reply by Jason Edge on Thursday. 6 Replies 0 Likes

First, A Big Thank You to CLC Chief Judge Bill Anderson for taking on this daunting task of overhauling the CLC judging system. The old system was very good, however, I believe what Bill and the…Continue

front seat crest

Started by Frank Murch in 1963/64 Cadillac Specific Discussion. Last reply by Frank Murch on Tuesday. 3 Replies 0 Likes

Original seats had a crest on the center arm rest. Does anybody know where I could embose a crest in new material for a reupolstry?Continue

Blog Posts

1963 RHS A/C kick panel - photos needed

Posted by SK on June 2, 2025 at 2:20pm 2 Comments 0 Likes

Could someone post front and back photos of the 1963 right-hand kick panel with A/C?

My car didn’t come with the original kick panels, so it's a bit of a mystery to me how I should cut the backing board and carpet to fit around the A/C.

Many thanks,

-Samu

Edelbrock Carb Block off Plates

Posted by Chase on March 12, 2025 at 2:05pm 14 Comments 1 Like

Hey guys,

I have installed the same Edelbrock carb and have done everything the same as Jason’s carb and intake project. In the spring and summer months the car starts, runs and idles great! In the fall and winter months on a cold start, the car starts awful and wants to die until it warms up. I have to keep my foot on the throttle until it warms up or it will idle just terrible and try to die. Once it’s warm, it runs fantastic! Whats going on here? I was thinking of removing the…

Continue