Just wondering if anyone knows of a place to get interiors done in the Pacific Northwest. I'm looking at seats, door cards and headliner. I live in the Tacoma Washington area so west side is preferable .  appreciate any help.  

Views: 107

Reply to This

Replies to This Discussion

Best to go to cruise ins and talk to people. Find out where they go and who is known for a good job.

That's Russ, thats tough this time of year in the PNW as its not cruise season. Everyone hibernates up here and works on their cars. 

Best to go to cruise ins and talk to people. Find out where they go and who is known for a good job.

Check out and join a Cadillac LaSalle Club (CLC) region in your area.   They will be an invaluable resource for networking and finding local recommendations. Here is one I see on the list of CLC regions in WA state on the Chapters & Regions page at https://www.cadillaclasalleclub.org/general/custom.asp?page=regions... :

PACIFIC NORTHWEST (1966)
Robert A. LeCoque
P.O. Box 3025
Renton, WA 98056-5025
(206) 799-6585
rLecoque@msn.com
WEBSITE

If into a member of the CLC join them at www.cadillaclasalleclub.org/join    They currently have a free 6 month free membership deal through now and the end of the year!

Thank you Jason, I will look into that 

try these guys they supposedly took over from the guy that did a great job on mine many years ago. it looked factory correct when I got it back including the crests embossed in the leather.The company is -- Texas Auto Upolstery --in Vancouver Washington
The new owner is --Emilio @ 360 771 3565

Thank you Maurice I will look them up. 

RSS

Photos

  • Add Photos
  • View All

Forum

Happy Father's Day!

Started by Jason Edge in 1963/64 Cadillac Specific Discussion. Last reply by Tony and Ginny 429 3 hours ago. 1 Reply

Happy Father's Day to my dad, Sam Edge. He was there in the beginning with…Continue

622 nss 63 tilt

Started by Kim K Kaiser in 1963/64 Cadillac Specific Discussion. Last reply by Tony and Ginny 429 14 hours ago. 7 Replies

Previously, i mentioned the  bu lights didnt work, and conversatiin went to nss.   Mine has the two jumped wire bypass so car will go in drive/start.Got the switch out and the outer tract plastic is…Continue

Timing chain help

Started by Cody in 1963/64 Cadillac Specific Discussion. Last reply by Tony and Ginny 429 yesterday. 3 Replies

I have the front of my engine taken apart to replace the timing chain and gears. According to the manual it says to remove the cam gear and chain together then the crank gear.I can’t for the life of…Continue

Current 1963/64 Cadillac Listings on eBay

Started by Jason Edge in For Sale. Last reply by Jason Edge yesterday. 0 Replies

To see all 1963/64 Cadillacs Listed on eBay in the USA…Continue

Tags: ebay

Blog Posts

New vehicle in the club

Posted by Patrick Westphal on June 17, 2021 at 4:00pm 1 Comment

I was successful in getting a vehicle from the New York contact I talked about at the last club meeting. I am still trying to figure out how to post a picture of the vehicle that is tied with this comment so if you see a random picture of a black convertible in a yard, that's me haha.  …

Continue

Torque converter grab when idling in Drive

Posted by Cliff Johnston on June 14, 2021 at 8:47pm 2 Comments

Hi Everyone, been quite a while since i have been on here.

I have had an issue with the idle on my 64 Coupe Deville ever since i have had it.

With the Idle set high enough that it is smooth, but still a nice idle, the RPM seems only slightly too high for the stall of the Torque Converter. And therefore it tends to sit there and grab and lunge a bit. So until now, i have been putting the car in Neutral at the lights to stop this happening.

I've had the car dyno tuned and…

Continue

Can you help? Driveshaft Question....

Posted by Chris on May 30, 2021 at 8:55am 1 Comment

Hello!

Newbie to the group here - we have already found tons of invaluable information on the board, so thanks! We are restoring a 1963 Series 62 Convertible. We are wondering if anyone knows of a source to buy the propellor yoke flange (that bolts to the pinion flange) for the driveshaft? One of our ears partially broke off. Not sure if we can buy just the yoke flange as an aftermarket part, or if it has to be rebuilt by a welder/fab guy? Maybe a salvage yard for a source? Again, any…

Continue

Thank you Kurt re: VIN location

Posted by Robert Pellow on April 19, 2021 at 1:07pm 0 Comments

I just wanted to say a thank you to Kurt for steering me to the tech tips page on V.I.N. locations.  Excellent information.  Thanks a bundle.

Robert Pellow

Videos

  • Add Videos
  • View All

© 2021   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service