Hey all,  the noise im lonking here comes and goes.  Its not normally at startup, kind of shows after abput 10 minutes  and most hearable at idle.  Last i was hraering it when it was really hot out, but it went away.  I believe the heat out was causing a vapor problem.  I took car out in hi 80s for abput 40 minute ride, got to desination.   Car never went over 1/3 on temp gauge, thought i was good,  Got out, went in for about 2o min and car wouldnt start.  Fuel in bowl was sbout an eighth high. Being 40 min from home, i panicked, got on internet searched vapor lock and found i could try and pour cold water on fuel pump, lines to try and drop temp.   After about ten minutes of pouring on pump and lines, it started!  Got home no prob.  Outsode temp had dropped to 70s.

The "noise" had not been around for a week or two,  then today, back again.  

Rrason i explained above was for recent driving for reference.

Here is the noise. It was dark out when i took it, seems more toward back of engine.  Any thoughts here

Thanks for listening


https://youtu.be/a8CsUlxv5IE

Facebook Facebook

Views: 631

Reply to This

Replies to This Discussion

Well i think i got it figured,  it was pointed out the notch on the end of shaft not pointed in right dirction. So had to flip it back, reset the arms, and result was oil flowing up and out of top of rocker arm, down the spine, onto springs,   the squuek was not present at all.

https://youtu.be/bv_I6hi4jDY

Thanks to all who helped me out.  Learn something new everytime i fiddle w this thing

Congrats on the fix. I had assumed rocker arm shaft assemblies were installed correctly...especially after all the discussion we had prior about following the shop manual (in pariticular rocker arm installation on section 13.8, page 9-17 in shop manual) and the fact they had to be installed correctly. I pretty much always get things wrong when I assume these days. Not sure how many miles were on the engine with rocker arm shaft on backwards but hopefully no damage done. Regardless, fire it up and go enjoy a ride in the Caddy!

RSS

Photos

  • Add Photos
  • View All

Forum

Replace Choke Tube or Install Electric Choke?

Started by Michael Stinson in 1963/64 Cadillac Specific Discussion. Last reply by CHRIS CARLSON yesterday. 8 Replies

My mechanic has sourced a choke housing and new internals.  As you might expect, the choke tube is damaged and or clogged.  My options are to either replace the choke tube, or my mechanic recommends…Continue

Tags: Electric Choke, Choke Tube

TH400 Dipstick Tube Seal

Started by Logan Robb in 1963/64 Cadillac Specific Discussion. Last reply by Michael Buonaccorso on Monday. 10 Replies

In my “rebuild” of the transmission, I ordered a dipstick tube seal. However, I’m not sure if the right one came or how to best install the seal. I am wondering if anyone has replaced this seal OR…Continue

window regulators

Started by Frank Murch in 1963/64 Cadillac Specific Discussion. Last reply by Frank Murch on Saturday. 2 Replies

For years my winds have seemed to be looser and less accurate than most modern windows.  I am thinking the soft parts are worn.  Has anybody gone through thier window regulators and felts to restore…Continue

Correct whitewalls

Started by Richard Stanley in 1963/64 Cadillac Specific Discussion May 29. 0 Replies

 I just replaced my tires from Diamondback (I had bad results in the past from Coker).  It was the second time, due to the age of the tires.  About 18 years ago Diamondback made custom whitewalls…Continue

Tags: width, whitewall, correct

Blog Posts

1963 RHS A/C kick panel - photos needed

Posted by SK on June 2, 2025 at 2:20pm 2 Comments

Could someone post front and back photos of the 1963 right-hand kick panel with A/C?

My car didn’t come with the original kick panels, so it's a bit of a mystery to me how I should cut the backing board and carpet to fit around the A/C.

Many thanks,

-Samu

Edelbrock Carb Block off Plates

Posted by Chase on March 12, 2025 at 2:05pm 14 Comments

Hey guys,

I have installed the same Edelbrock carb and have done everything the same as Jason’s carb and intake project. In the spring and summer months the car starts, runs and idles great! In the fall and winter months on a cold start, the car starts awful and wants to die until it warms up. I have to keep my foot on the throttle until it warms up or it will idle just terrible and try to die. Once it’s warm, it runs fantastic! Whats going on here? I was thinking of removing the…

Continue

'63 Tailfin Tales

Posted by Mark Mata on February 22, 2025 at 5:00pm 9 Comments

New old stock seat material

Posted by Ray Schick on August 22, 2024 at 6:25pm 2 Comments

I bought this seat material thinking that it’s…

Continue

Videos

  • Add Videos
  • View All

© 2025   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service