Ok.  Out today,  rear brakes got very hot, again.  1st time in aweek.  Almost like they are resetting back.  Anyway decided to fix the axle leak .  

Well, took off hub, and undid bolts behind brake assembly,  didnt even need axle puller,  a good hard yank, it cam out.  First thing i noticed ,there was a torn gasket looking piece that seems to sit behind the brakes shoe assembly and goes between the brake shoe assembly and the hub that the assebly attaches to.  It was damged.

I got the axle part out,  bearing seemed smooth turning.  O ring was intact but scuffed.  

Pictures attached of parts w notes.

So.  According to u tube, this type assembly requires the bearing and seal be cut off w grinder.   

Is that correct, or do i need to rent a specific tool for this.

Secondly, i dnt remeber seeing that gasket that fits behind the brake shoe assembly,  only one i see in book is the paper one.   Is there another one and what would it be called? 

Any help here forward would be appreciated imensely  

Facebook Facebook

Views: 786

Attachments:

Reply to This

Replies to This Discussion

you got a good deal on the bearings and seal.  i paid about 350 for the set, from usaparts..8.00 for the set of gaskets on both sides,, 

Mack, just wanted to say thanks for providing the detailed info on the parts.  Much appreciated!

I found them on eBay. It's tricky to put them in so be creative to not bend the trailing arms :)

RSS

Photos

  • Add Photos
  • View All

Forum

Bleeding brakes

Started by Dave Fehrle in 1963/64 Cadillac Specific Discussion. Last reply by Russ Austin 9 hours ago. 3 Replies

I have finished replacing all the rear suspension and am at the last item, which is bleeding the rear brakes. I am using the Jason Edge vacuum pump method and all went well with the rear passenger…Continue

Front grill

Started by Phillip Hill in 1963/64 Cadillac Specific Discussion. Last reply by Dennis P. DiBari yesterday. 8 Replies

Hi everyone im currently restoring my my front grill due to some previous clown painting it with silver frost paint and doing a dodgy job I would like to know what parts of the grill are anodised.it…Continue

Getting hot when going fast…

Started by Mack in 1963/64 Cadillac Specific Discussion. Last reply by Dennis P. DiBari on Tuesday. 6 Replies

So… I do have a few of 63 Coupes, all have same setup with carbs, Pertronix, shroud, new US Radiator radiators etc … but only one of them gets a bit hot when I am hauling faster than 60mph and car…Continue

Rainstorm out of nowhere!

Started by Logan Robb in 1963/64 Cadillac Specific Discussion. Last reply by Dennis P. DiBari on Monday. 1 Reply

After dinner last night, we went for a quick cruise as the weather was cooler and the sun set was looking really good!Out of nowhere, a pop up shower appeared overhead and down-poured as we were…Continue

Blog Posts

1963 RHS A/C kick panel - photos needed

Posted by SK on June 2, 2025 at 2:20pm 2 Comments

Could someone post front and back photos of the 1963 right-hand kick panel with A/C?

My car didn’t come with the original kick panels, so it's a bit of a mystery to me how I should cut the backing board and carpet to fit around the A/C.

Many thanks,

-Samu

Edelbrock Carb Block off Plates

Posted by Chase on March 12, 2025 at 2:05pm 14 Comments

Hey guys,

I have installed the same Edelbrock carb and have done everything the same as Jason’s carb and intake project. In the spring and summer months the car starts, runs and idles great! In the fall and winter months on a cold start, the car starts awful and wants to die until it warms up. I have to keep my foot on the throttle until it warms up or it will idle just terrible and try to die. Once it’s warm, it runs fantastic! Whats going on here? I was thinking of removing the…

Continue

'63 Tailfin Tales

Posted by Mark Mata on February 22, 2025 at 5:00pm 9 Comments

New old stock seat material

Posted by Ray Schick on August 22, 2024 at 6:25pm 2 Comments

I bought this seat material thinking that it’s…

Continue

Videos

  • Add Videos
  • View All

© 2025   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service