List Mates,

My '64 De Ville Conv. front door window chrome trim needs to be replaced.  The chrome on both front door window his getting a little bit of pealing off.  

I have the chrome replacement channels, and flat rubber window channel lining tape.  I've watched Youtube videos on how to remove the old channels and seat new ones.

This seems like a fairly long an complicated project because it appears that I have to remove door panels and remove the windows from the doors and then  to put the windows back in the doors and adjust to glide properly.  

Because I can be a bit impatient and clumsy at times, I'm a bit anxious about removing the windows from the doors and removing the chrome trim without shattering the glass.  Any tips or things I should consider (like having a professional do it :-). )before I embark on this challenging project?

Mike

Views: 25

Reply to This

Replies to This Discussion


Once you replace the required parts  in the door  - the chrome and window channels  etc —keep the inside panel off the door off for a while —until you get the window to go up and down as it should from some adjustments that may be needed to get that working as it should 

That took me a few days  driving around to get  it right myself 

The doors originally had an internal skin to keep rain water from getting to the inside  part of the inner door( cabin side ) 

It was originally a  kind of treated  wax paper that may possibly  be deteriorated  and gone by now 

It can be replaced with 4 mil plastic and duct tape to renew that water protective  barrier that it is 

Be sure the weep holes in the bottom of the doors  are free of debris and area  cleaned out  so any water can escape that gets into the outside part of the  inner door  which is separated by the above water barrier 

Not much chance of braking the glass as it is thick and would take a lot of  extreme abuse to damage it (  it is shatter proof glass ) 

A few tips that  should help —get her done

Enjoy 

RSS

Photos

  • Add Photos
  • View All

Forum

Rear main seal. 63

Started by Kim K Kaiser in 1963/64 Cadillac Specific Discussion. Last reply by Tony and Ginny 429 8 hours ago. 3 Replies

My rms is leaking again.  I hv cked all other options for leaks and its none of those.  Ie, oil presdure, valve covers, etc.  So i called egge to order another one.  I asked the guy wat contack…Continue

Selling 1964 Coupe Deville Parts

Started by Gary Smiley in For Sale. Last reply by Gary Smiley 10 hours ago. 2 Replies

What I  have are many extra original, hard-to-find 1964 Cadillac Coupe Deville Parts (from donor car).…Continue

Tags: doors, hood, engine

Classic Cadillac Parts For Sale - Misc Items

Started by Jason Edge in For Sale. Last reply by Jason Edge 16 hours ago. 275 Replies

I have posted a few Misc items over on my Classic Cadillac Parts Facebook page at…Continue

Tags: classic cadillac parts, classiccadillacparts

Blog Posts

Rumble Sound at 55-60 mph

Posted by Ray Schick on September 20, 2021 at 10:45pm 6 Comments

64 Coupe DeVille , while driving at 55-60 mph I have a oscillating rumble sound . Steering wheel does not shake or vibrate . Transmission mount looks good .Tires were replaced 2 years ago balanced and rebalanced recently. Axel bearings were just replaced, rear differential assembly was just replaced with a Posi track ,pinion bearings good. Fresh gear lube. Driveshaft checked and balanced the other day ,new center bearing installed and new bearing carrier assembly too. Trying to figure this…

Continue

1963 series 62 convertible transmission issue

Posted by Matthew VanDeWater on June 22, 2021 at 3:03pm 1 Comment

Hello I've been restoring a 63 for way to many years. Down to almost done, but have issue with trans linkage, when column in park shift rod 2 inches short. everything original. been trying to find picture of manual rod hooked up from under car to see position of linkage. was wondering if anybody has access for pictures. I wanted to see if my manual linkage is bent  wrong out of the trans if somebody dropped the trans or something. Doesn't make sense why it doesn't work. Thanks for any input…

Continue

New vehicle in the club

Posted by Patrick Westphal on June 17, 2021 at 4:00pm 1 Comment

I was successful in getting a vehicle from the New York contact I talked about at the last club meeting. I am still trying to figure out how to post a picture of the vehicle that is tied with this comment so if you see a random picture of a black convertible in a yard, that's me haha.  …

Continue

Torque converter grab when idling in Drive

Posted by Cliff Johnston on June 14, 2021 at 8:47pm 2 Comments

Hi Everyone, been quite a while since i have been on here.

I have had an issue with the idle on my 64 Coupe Deville ever since i have had it.

With the Idle set high enough that it is smooth, but still a nice idle, the RPM seems only slightly too high for the stall of the Torque Converter. And therefore it tends to sit there and grab and lunge a bit. So until now, i have been putting the car in Neutral at the lights to stop this happening.

I've had the car dyno tuned and…

Continue

Videos

  • Add Videos
  • View All

© 2021   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service