I'm having a shop replace outside seals/gaskets on engine and tranny. Engine was losing 3/4qt. every 250mi. So far only a small drip on rear main. 

Bought an outside seal kit for tranny. sealed up dipstick, shift shaft, that went fine. Pan not so good. Went out and found a puddle under tranny for the second time after sitting the weekend. Going in for the third time to try and get it right. Are we missing something?? The shop about only deals with classic and performance stuff so he ain't no fly by night. I know you're only guessing on diagnosis but thought I'd throw it out there

Thanks for any suggestions. 

Tom B

Facebook Facebook

Views: 112

Reply to This

Replies to This Discussion

Try a straight edge over the face of the pan.

Over time, often to fix leaks, folks swing off the bolts like their doing up wheel nuts, which will buckle/distort the clamping face.

The pan can be beaten back into shape ok.

Could this be a torus check valve problem? after sitting a couple days I end up with a puddle under the tranny. If so, I assume this is a tranny tear down to fix

RSS

Photos

  • Add Photos
  • View All

Forum

seat foam replacement

Started by Kevin Robles in 1963/64 Cadillac Specific Discussion. Last reply by Kevin Robles 14 hours ago. 3 Replies

does anyone out there have any experience with seat foam replacement on  a 63/64 Cadillac.  I had my seats reupolstered  many years ago in original leather/fabric and they still look great, but the…Continue

1963 carter afb carbureter stainless steel shim

Started by tim sparks in General Discussion 20 hours ago. 0 Replies

anybody have an xtra stainless steel shim for 1963 carter afb carb. thank youContinue

Timing cover corrosion

Started by CHRIS CARLSON in 1963/64 Cadillac Specific Discussion. Last reply by Dennis P. DiBari yesterday. 1 Reply

Hey fellas if you're rebuilding your 429 check your timing cover for corrosion behind the water pump  Russ and I had 429 engine number two on the dyno today had shimed the oil pump spring for a…Continue

Convertible bumper jack

Started by Alan Clark in 1963/64 Cadillac Specific Discussion. Last reply by Alan Clark yesterday. 13 Replies

My car lacks the mechanism or spring needed to hold the jack in the storage slot on the right side of the trunk.  Anyone have a picture of the item I should find?Continue

Blog Posts

1963 RHS A/C kick panel - photos needed

Posted by SK on June 2, 2025 at 2:20pm 2 Comments

Could someone post front and back photos of the 1963 right-hand kick panel with A/C?

My car didn’t come with the original kick panels, so it's a bit of a mystery to me how I should cut the backing board and carpet to fit around the A/C.

Many thanks,

-Samu

Edelbrock Carb Block off Plates

Posted by Chase on March 12, 2025 at 2:05pm 14 Comments

Hey guys,

I have installed the same Edelbrock carb and have done everything the same as Jason’s carb and intake project. In the spring and summer months the car starts, runs and idles great! In the fall and winter months on a cold start, the car starts awful and wants to die until it warms up. I have to keep my foot on the throttle until it warms up or it will idle just terrible and try to die. Once it’s warm, it runs fantastic! Whats going on here? I was thinking of removing the…

Continue

'63 Tailfin Tales

Posted by Mark Mata on February 22, 2025 at 5:00pm 9 Comments

New old stock seat material

Posted by Ray Schick on August 22, 2024 at 6:25pm 2 Comments

I bought this seat material thinking that it’s…

Continue

Videos

  • Add Videos
  • View All

© 2025   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service