Steering Coupler (Rag Joint) 1963 Cadillac with Tilt Wheel
Hi all,
I am in the process of replacing my steering gear box. Upon removal I notice that the rag joint is showing some stress, my car has tilt wheel. My question is, are the rag joints common between tilt and non-tilt cars or are they different? So before I start researching for a replacement part I want to be sure I get the correct one. Thanks everyone.
Jim
Replies to This Discussion
-
Permalink Reply by Robert Alan Shannon on
-
According to the info in Tilt Steering Conversion under HELP Topics, they are different. I don't know the difference, mines non-tilt. HTH
-
Permalink Reply by Jason Edge on
-
Hi Jim, Tilt is smaller diameter on the column side. I have very nice, used non-tilt rag joints with excellent masticated rubber, ground wire etc. for $35 + s/h. If you need tilt I would need to double check. Email at jasonedge@nc.rr.com if interested and provide a shipping address.
-
Permalink Reply by Jim Pino on
-
Hi Jason thanks for the quick response. I figured there had to be some difference. My car has tilt, if you get the chance to see if you have one I would appreciate it. Jim
-
-
I checked and I am out of the tilt rag joint. If Russ or one of the others don't have one, give me a shout at jasonedge@nc.rr.com and I will put you on the Wait List for one.
Members
Forum
Power Booster Install
Started by Rob Spring in 1963/64 Cadillac Specific Discussion yesterday. 0 Replies 0 Likes
Hey! I’ve seen the 63/64 power booster and master cylinder combination has been covered very clearly. I’m in the process of replacing mine. I was hoping someone could give me insight on a specific…Continue
Complete Front End Rebuild
Started by Logan Robb in 1963/64 Cadillac Specific Discussion. Last reply by Mark Mata yesterday. 1 Reply 0 Likes
I meant to make this a priority over the winter and didn't get that far. I've tried to source all the parts individually, but that is a daunting task. Partly because I don't want to miss any…Continue
1964 Cadillac Deville Neutral Safety switch and Oil Filter Housing Assembly
Started by Michael Monson in Wanted to Buy. Last reply by Russ Austin on Wednesday. 1 Reply 0 Likes
Hello, possibly looking a neutral safety switch for a 1964 Deville with the TH-400 and tilt steering. Also, possibly looking for an oil filter housing assembly for a 1964 429 motor. Starting to get…Continue
A Shout Out to Alan Grist & Some Pictures of His 1964 Series 62 4W Sedan
Started by Jason Edge in General Discussion. Last reply by Dennis P. DiBari on Wednesday. 2 Replies 0 Likes
As they say, Better Late Than Never!I want to give a shout out to 63/64 Chapter Member Alan Grist, who brought his 64 Series 62 Four Window Sedan, to the 2025 CLC Winter Board Meeting in Chattanooga,…Continue
Blog Posts
Edelbrock Carb Block off Plates
Posted by Chase on March 12, 2025 at 2:05pm 13 Comments 0 Likes
Hey guys,
I have installed the same Edelbrock carb and have done everything the same as Jason’s carb and intake project. In the spring and summer months the car starts, runs and idles great! In the fall and winter months on a cold start, the car starts awful and wants to die until it warms up. I have to keep my foot on the throttle until it warms up or it will idle just terrible and try to die. Once it’s warm, it runs fantastic! Whats going on here? I was thinking of removing the…
ContinueNew old stock seat material
Posted by Ray Schick on August 22, 2024 at 6:25pm 2 Comments 0 Likes
I bought this seat material thinking that it’s…
Loud air moving sound within carb with cleaner removed
Posted by Dave Fehrle on March 23, 2024 at 3:23pm 8 Comments 1 Like
While checking my Carter carb with engine running, I took the air cleaner off and there was a very loud hissing sound of air. I placed a piece of paper over the carb and it didn’t move up or down, is this normal?
Events
© 2025 Created by Jason Edge.
Powered by
