I checked the Help page and did a search on the site but didn't see any subjects on steering play/slack.  Since I had someone complete a front end rebuild (Kanter kit, all the control arm bushings, tie rods, sway bar, ball joints, everything) on my 64 deville conv,  there is quite a bit of play in the steering.  At times it's hard to keep the car straight going down the highway.  When it starts drifting and you go to correct, it almost overcorrects and gets scary weaving back and forth trying to keep it center.  I'll try to use my original Maintenance manual to see how to address (maybe there's an adjustment on the worm gear or other adjustments on the steering box?) but wasn't sure if others have had similar issues.....  any help is appreciated.   thanks, Nile

Views: 78

Reply to This

Replies to This Discussion

Hi Nile,

     After all that front end work, there is an adjustment on the steering box, but it shouldn't be overdone.  On top of the box there is an allen key hole, set inside a nut.  You can see this looking over the fender and may have  get underneath the wrench it.  The nut (maybe 9/16 wrench) is loosened and the allen hole can be tightened 1/4 of a turn clockwise.  Hold the allen key in place while tightening the nut back up.  Unless the box is very old and worn, you might get some slack taken out.  I wouldn't do much more than 1/4 turn.  See if this helps at all.

Dennis DiBari, NY

Hi Nile,

     One more thought on the play in the steering.  Did you test/inspect you Rag Joint?  That can cause a lot of play in the steering as well.  I forgot to mention it with my first rejoinder.  Look at this first as it may be the culprit.  The slight steering box adjustment is your last resort.

Dennis DiBari  

Thank you Dennis for the help!  I love this website for this:  passing on knowledge.  I'm going to give this a shot!  thanks much.  Nile

Hi Nile,

     You are welcome!  Remember, if you adjust the steering box, no more than 1/8th to 1/4 turn clockwise.  The rag joint play is primarily important.  Best of luck with it!!

Dennis DiBari

RSS

Photos

  • Add Photos
  • View All

Forum

1963 & 1964 Equipment Percentages

Started by Jason Edge in 1963/64 Cadillac Specific Discussion. Last reply by Jason Edge 14 hours ago. 3 Replies

Here is a list of equipment percentages I had pulled from the Ward Automotive Yearbooks for 1963 and 1964 and have used for several trivia questions. I thought I would share the entire list as seen…Continue

!964 Deville Front Bumper

Started by Patrick Westphal in For Sale. Last reply by Jason Edge on Monday. 1 Reply

Hey everyone,I have a set of front bumpers, both ends and the center section, that I am looking to sell.  If you are looking for these contact me and we will talk about it. …Continue

Which are best Shocks for 64 that are closest to Original in Ride Quality?

Started by Norman Silverman in 1963/64 Cadillac Specific Discussion. Last reply by Norman Silverman on Sunday. 5 Replies

Hello AllI am thinking about replacing the shocks on my 64 SDV. I want to do so with units that are closest to what was originally in the car in so far as ride quality. I believe these were gas…Continue

1964 Cadillac Owners - Are You Missing the Inner Fender to Frame Rear Brace Rods?

Started by Jason Edge in 1963/64 Cadillac Specific Discussion. Last reply by Dennis P. DiBari on Sunday. 1 Reply

Last night I was installing the freshly cad plated inner fender to frame rear support brace rods and remembered how this has been often missing on the many parts cars I have brought in. The thing is…Continue

Blog Posts

1963 RHS A/C kick panel - photos needed

Posted by SK on June 2, 2025 at 2:20pm 2 Comments

Could someone post front and back photos of the 1963 right-hand kick panel with A/C?

My car didn’t come with the original kick panels, so it's a bit of a mystery to me how I should cut the backing board and carpet to fit around the A/C.

Many thanks,

-Samu

Edelbrock Carb Block off Plates

Posted by Chase on March 12, 2025 at 2:05pm 14 Comments

Hey guys,

I have installed the same Edelbrock carb and have done everything the same as Jason’s carb and intake project. In the spring and summer months the car starts, runs and idles great! In the fall and winter months on a cold start, the car starts awful and wants to die until it warms up. I have to keep my foot on the throttle until it warms up or it will idle just terrible and try to die. Once it’s warm, it runs fantastic! Whats going on here? I was thinking of removing the…

Continue

'63 Tailfin Tales

Posted by Mark Mata on February 22, 2025 at 5:00pm 9 Comments

New old stock seat material

Posted by Ray Schick on August 22, 2024 at 6:25pm 2 Comments

I bought this seat material thinking that it’s…

Continue

Videos

  • Add Videos
  • View All

© 2025   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service