When I purchased my '63 Cadillac 11 months ago, it had ice cold a/c with an R12 system. The seller advised me that it needed to be "topped off" every year or so. For the small amount of driving that I did with it in the summer months (when it wasn't tied up in the shop for other repairs), I did notice the temps from the vents getting gradually warmer. I also noted that while traveling at highway speeds, even when things were working properly, the air would become much warmer until I slowed back down to city driving speeds. I attributed that to a vacuum related issue, and wasn't too concerned about it for the amount of highway driving that I do.
By the end of summer, I was getting outside air temperature inside the car, even though the compressor clutch was engaged. Now that temps are warming up again, I took it to my mechanic, who had recently purchased a small stock of R12. He topped it off, and when I headed home and noticed no difference, I used an infra-red thermometer to measure the temps of the air coming out of the vents, and found them to be the same as the ambient temps outside, about 67 - 72 degrees. I called him last week to ask if he had done either a dye or sniff test, and that's when he told me that he didn't have the proper recovery equipment, and only added a can or two to whatever remained in the system. While I was examining the system at home this week before calling him, I noted that there is no activity in the sight glass of the dehydrator receiver, even though the compressor clutch is cycling properly whenever I engage the a/c. I have an appointment for next Wednesday to see what the next step is. His suggestion over the phone is that "maybe the compressor is bad."
Over the past couple of days, I have called a number of auto a/c shops in the area, and no one does R12 anymore. The one guy who still has the equipment to do it can't find product anywhere. My question to you guys is if it is time to bite the bullet and make the switch to R134a? I would like to keep my 34,000 mile car in as original condition as possible, but the time is probably near when R12 will no longer be available anywhere, so I'm concerned about funneling money into maintaining this system only for its originality.
I did read the great articles on this site in the "help" column related to this subject, but since it was posted back in 2016-2017, I'm sure a lot has changed since then. I appreciate any updated thoughts on this, and my apologies for being so long winded.
Terry
Tags:
Terry
Contact ——Old Air products - they will tell you what you will need to go to 134 a in our year Cadillac AC systems
Enjoy
Thanks Tony. Every AC shop in my area that I've spoken to has offered to do a conversion to 134a, so that isn't a problem. I'm still sitting on the fence, as I have read that 134a is being phased out and replaced with a new refrigerant, so I don't want to have to go through the process twice over the next few years.
I did look at Old Air Products website after reading your reply yesterday, and was a little disappointed in how it was laid out. Once you enter the year, make and model of your vehicle, you are linked to a page with dozens of individual AC parts that are available for that car, but no "package" consisting of the parts that would be needed to do the conversion. I guess a phone call to them would solve that issue, but it just seems to be one more step that could have been avoided.
I spoke with a CLC member at a regional meet yesterday who told me he uses a refrigerant in his '60 Cadillac that is not R12, and doesn't require any type of modification to the AC system, so I will be getting some more information on that from him this week.
Let us know what you find out about a new refrigerant to be using
R-12 is now illegal to use and very hard to be finding if at all but I would use it if you can find it
Calling Old AC products is the way to go when and if needed for the 134a
Enjoy
Correction that is — Old Air Products to be calling
Enjoy
I could be wrong Tony, but my understanding is that R12 is not illegal to use, but you have to have a license to purchase it (if you can find it), and must have the proper recovery equipment to prevent it from being released into the atmosphere when you are discharging/recharging the AC system. And of course it can no longer be manufactured. But the day will come when the dwindling supply of NOS and recaptured R12 will run out, and the price of it will be crazier than it is now as we approach that point..
Started by Russ Austin in General Discussion. Last reply by Jason Edge 6 hours ago. 10 Replies 0 Likes
For sale is the #1 frame cross member that has the vehicle VIN on it. Comes with the matching Arizona title in my name. This is legal in Arizona, please check your state laws before putting this on…Continue
Started by Matti Roth in 1963/64 Cadillac Specific Discussion. Last reply by Matti Roth yesterday. 2 Replies 0 Likes
The steering gear in my 64 is leaking from steering shaft side and I need to rebuild it. I have used steering gear from 70`s Monte Carlo available. Is there any reason why not to use that temporarily…Continue
Started by Jason Edge in 1963/64 Cadillac Specific Discussion. Last reply by Jason Edge yesterday. 1 Reply 5 Likes
To see all 1963/64 Cadillacs Listed on eBay in the USA…Continue
Tags: ebay
Started by Jason Edge in Chapter Discussion. Last reply by Jason Edge on Wednesday. 404 Replies 4 Likes
Tags: chaptermember, newmember
Posted by CHRIS CARLSON on March 20, 2023 at 11:32pm 3 Comments 0 Likes
I'm having my steering sector rebuilt, and considering changing it from 20-1 ratio 4.2 turns lock to lock to 3.5 turns lock to lock @ 16-1 ratio, If i change from a 3 1/4" box to a 3" box i could have a 14-1 Ratio steering response would be faster, shorter distance to turn the wheel to get a response, has anyone done this? and how do you like it? thank you
Posted by Willem Bol on March 13, 2023 at 11:33am 2 Comments 0 Likes
Hallo,
Can somebody help me finding a dashboard clock for my 1964 Cadillac DeVille Convertible?
Thank you in advance,
Willem Bol
The Netherlands
Posted by Robert Schles on February 21, 2023 at 11:45am 2 Comments 0 Likes
I've looked at the usual rubber sources but couldn't find any.
Posted by Curtis Dover on January 2, 2023 at 5:23pm 0 Comments 0 Likes
Hey guys, I need some help. Could someone send me some pictures on how the first hood release lever on a factory 1964 Cadillac is set up, where it comes though the grille. Not the secondary one. I need to know where the thumb or finger position is located through the grille. Is it above or below the center grille molding piece? Mine seems to be positioned behind the center molding piece and will not adjust above or below the molding. I have a wire tied to it to release it…
Continue
© 2023 Created by Jason Edge.
Powered by