My 64 Sedan De Ville has a vibration starting at 20 and stops at 25 to 30 mph before that and after that car runs smooth. Thinking it might be an exhaust vibration I put a little sill glide silicone on the rubber hangers which are only 10 years old and in very good condition. This did not help. There is no vibration when car idles or when I rev it up. The car runs and shifts great. I have just recently noticed this vibration. I have owned this car for over 10 years I bought it with 18000 miles which really are original and now have 21000+ miles on it. The condition of this car is mint inside and out point being it's not beat. It's all original, I have done a lot of mechanical things but have never touched the drivetrain. Any thoughts would be much appreciated. Thank you, Ron Perry, the only other thing I might add is the vibration seems to be coming from drivers' side, but it is really hard to determine.

Views: 166

Reply to This

Replies to This Discussion

It could be a few things. Probably the most common cause is drive line angle. The angle shifts when motor mounts, especially the transmission mount collapse. This discussion comes up often. You can use the search function (upper right-hand corner of this page) for search terms like "drive line angle" or "rumble" etc to see previous discussions. I'd check the condition of the transmission mount & go from there.

This is a great post.  I get a noticeable vibration at about 40 mph which stops at about 44 mph. I've had my mechanic look it over a number of times and we have been unable to locate it source of the vibration.  My mechanic has suggested that, although my tires are in great condition, they are quite old (2009), which suggests the car had been sitting for quite a while, and seems to have produced a very slight bulge in the tire from where it sat.  Once my car gets out of the paint shop, I'll be putting new tires on her. I hope that cures the problem. If not, I'll be having my mechanic inspect the drive train and rubber.

I want to thank everyone for all the great replies to my post. All of your information has been very helpful. I did look at all my rubber components first based on cars condition and age seems the most logical place to start. I did notice some fine cracks on the transmission mount, but engine mounts look ok. I also looked as best I could at the rubber bushings at the rear of car and did not see any noticeable cracks. My tires are over 10 years old, but tread is excellent so that's another spot for me to look. I have my work cut out for me! Thanks again to everyone Ron Perry

Starting front to rear; Collapsed trans mount, worn tail shaft bushing, bad carrier bearing or support, worn CV joints, worn bushings in the lower control arm. ( the rear bushing gets distorted and allows the pinion angle to change) Unbalanced drive shaft.  Bad rims/tires, 



  • Add Photos
  • View All


Cadillac Original Ads - 1964 Standard Ads

Started by Jason Edge in 1963/64 Cadillac Specific Discussion. Last reply by Dennis P. DiBari 10 hours ago. 3 Replies

Just as I had done last December with the standard 1963 Cadillacs magazine ads, I have started scanning my 1964 Cadillac Ads, and will post here one by one, then combine into a single photo album and…Continue

Pertronix 3 install and resistor wire

Started by Dave Fehrle in 1963/64 Cadillac Specific Discussion. Last reply by Dave Fehrle 19 hours ago. 18 Replies

A few questions on the resistor wire, what color is it in the pic? The yellow/blue or black? And connecting to the ACC on the fuse box seems easiest way to go with the new switched wire, but where…Continue

!964 429 Timing Cover

Started by Michael Monson in 1963/64 Cadillac Specific Discussion. Last reply by Russ Austin yesterday. 4 Replies

I'm looking to freshen up a few thing on the 429, and am looking for sources of the timing cover.  I.m new to the Cadillac world and have found that the Cadillac King sells a refurbished timing…Continue

Power Steering Hose Questions

Started by C. Van Tune in 1963/64 Cadillac Specific Discussion. Last reply by C. Van Tune on Tuesday. 6 Replies

My '64 Eldo's high-pressure P/S hose sprung a leak, so I want to change it (and the low-pressure hose.) My car is concours-level restored, so keeping as close to the stock fitment and appearance is…Continue

Blog Posts

accumulator dryer

Posted by CHRIS CARLSON on December 6, 2023 at 10:54am 0 Comments

Who rebuilds original AC  accumulator dryers for 1964 Cadillac? I have been on Classic auto air in Tampa FL wait list for over a year ,  There is one on Old air products web site that looks very similar to the original # 21-4214A but states it fits 1962 Gm cars, The one recommended for a 1964 Cadillac is half the length 21-4215A    What  is everyone using ? I would prefer to be as original as possible. Thanks

'63 Eldorado trumpet horn + 2 standard horns restoration

Posted by Les Eastling on November 15, 2023 at 10:34am 1 Comment

My son, unbeknownst to me, had all three of the horns on our 1963 Eldorado completely restored. We had recently added the Eldorado trumpet horn to the two standard horns and the sound was not very good... we had heard good ones so we knew something was not right... but there was not much we could do to get better sound from the 3 horns. 

There is a restoration service called The Horn Works who my son…


Clock ‘64 DeVille

Posted by Matt Vander Hooven on July 23, 2023 at 7:36pm 2 Comments

Is there still a member in the Detroit area that refurbishes clocks?

Matt VH

Spark Plug Heat Range

Posted by Patrick Westphal on July 7, 2023 at 10:00am 1 Comment

I found a diagram that illustrates the main factor in determining a spark plug heat range that I was trying to describe to you during the chapter get together.

Here it is:


The main factor is the length of the ceramic insulator from the middle of the spark plug to the tip (where the spark happens)  

The insulator…



  • Add Videos
  • View All

© 2024   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service