Windshield Washer (nozzle)?
My driver's side windshield washer is works "okay", but my passenger's side is barely pushing out any water. The hoses look good (reasonably soft without any apparent cracks or leaks) and the pump motor is working. Any tips on getting the nozzles to spray better or to direct the spray? Is there a way to clean the nozzles without pulling them out? Is the most reliable solution to just install a new pump?
Michael Vogler
Replies to This Discussion
-
Permalink Reply by Jason Edge on
-
The washer nozzle tip is screwed into the nozzle base. It is also how you set the spray pattern. You can screw the tip completely out with a medium sized screwdriver, being careful not to drop/lose the tip, and then take a needle or very small paper clip, etc and make sure the passage is clear. Sometimes those nozzles bases and/or tip get corroded and block passage. I do have very good nozzle tips ($5) or nozzle & tip ($10) if you need one. Below is an example of a good one showing the tip at the front.
-
Permalink Reply by Michael Vogler on
-
Jason,
Thank you for your advice on my windshield washers. I followed your instructions, removed and cleaned the nozzles and they now work great!!
Thank you!
Mike Vogler
-
-
Glad that helped.
Members
Forum
Dino Radiator Leak - Time to Recore!
Started by Jason Edge in General Discussion. Last reply by Bill Wolf on Friday. 36 Replies 0 Likes
I had brought up the topic of radiator leaks as a discussion topic for our Chapter Zoom meet-up this past Sunday and thought I would share on our website for everyone and probably do a more formal…Continue
front seat crest
Started by Frank Murch in 1963/64 Cadillac Specific Discussion. Last reply by Bill Wolf on Friday. 2 Replies 0 Likes
Original seats had a crest on the center arm rest. Does anybody know where I could embose a crest in new material for a reupolstry?Continue
64 Replacing dash illumination lights-how much has to come out to get to all of them?
Started by Norman Silverman in General Discussion. Last reply by Norman Silverman on Thursday. 11 Replies 0 Likes
Hello AllI have taken off my dash top and started replacing dash bulbs with LED's for greater visibility. Some questions:1) To replace the Gauge bulb it looks like easier access is had by removing…Continue
Correct whitewalls
Started by Richard Stanley in 1963/64 Cadillac Specific Discussion. Last reply by Bill Wolf on Wednesday. 3 Replies 0 Likes
I just replaced my tires from Diamondback (I had bad results in the past from Coker). It was the second time, due to the age of the tires. About 18 years ago Diamondback made custom whitewalls…Continue
Blog Posts
1963 RHS A/C kick panel - photos needed
Posted by SK on June 2, 2025 at 2:20pm 2 Comments 0 Likes
Could someone post front and back photos of the 1963 right-hand kick panel with A/C?
My car didn’t come with the original kick panels, so it's a bit of a mystery to me how I should cut the backing board and carpet to fit around the A/C.
Many thanks,
-Samu
Edelbrock Carb Block off Plates
Posted by Chase on March 12, 2025 at 2:05pm 14 Comments 1 Like
Hey guys,
I have installed the same Edelbrock carb and have done everything the same as Jason’s carb and intake project. In the spring and summer months the car starts, runs and idles great! In the fall and winter months on a cold start, the car starts awful and wants to die until it warms up. I have to keep my foot on the throttle until it warms up or it will idle just terrible and try to die. Once it’s warm, it runs fantastic! Whats going on here? I was thinking of removing the…
ContinueNew old stock seat material
Posted by Ray Schick on August 22, 2024 at 6:25pm 2 Comments 0 Likes
I bought this seat material thinking that it’s…
Events
Videos
© 2025 Created by Jason Edge.
Powered by
