Kevin Kennedy's Blog (12)

Anti-freeze collection bottle

I have a '63 cad Series 62. I was wondering if these cars had anti-freeze over flow collection bottles? When I turn my car off anti-freeze runs out of the over flow hose. If not is it ok to put one in?

Thanks, Kevin                         

Added by Kevin Kennedy on March 15, 2021 at 10:40pm — 7 Comments

What are these?

I am wondering what these are and what they were used for and if anyone has an extra one in the same color that they would like to get rid of?DSCF0930.JPG

Added by Kevin Kennedy on March 5, 2016 at 11:31am — 2 Comments

Skelly and the Caddy

This is Skelly my 7 ft skeleton. This is Skelly getting ready to go for a ride in St. Cloud in my '63 Cadillac on Halloween. It was a great time. People were pointing and laughing and getting others to look. When we were stopped at stop lights people were…


Added by Kevin Kennedy on December 17, 2015 at 10:05pm — No Comments

clock repair

If anyone has a clock that chatters and does not run I think that I have figured out how to fix it. In the pic there is a shaft with some gears, ratchet and winding mechanism. This shaft comes a little loose and drops down a little bit so that the ratchet ( green arrow ) does not line up with it's corresponding gear like it should and sometimes will not engage the teeth on the winding gear to wind the clock and will thus make the contacts chatter. To fix the problem you will need a 12 volt…


Added by Kevin Kennedy on November 28, 2015 at 2:56am — 2 Comments

'63 390 PICS

Before and after pics of my '63 390 in car…


Added by Kevin Kennedy on November 8, 2014 at 4:06pm — 2 Comments

hydramatic jetaway transmission

Does anyone have a working with no leaks jetaway tranny for a '63 caddy for sale? Is there a tranny out there that will work in my '63 caddy besides the jetaway?

Added by Kevin Kennedy on November 4, 2014 at 9:38pm — 1 Comment


my 1963 390 on a dyno

Added by Kevin Kennedy on April 13, 2014 at 5:48pm — 1 Comment

video down load

how can I down load my home made video?

Added by Kevin Kennedy on April 6, 2014 at 1:25am — 1 Comment

1963 390 caddy engine

Here is a pic of my recently rebuilt 1963 390 engine completely rebuilt from the ground up. Rebuilt by Thunder Valley Corvette Specialist in St. Joseph, Mn.

Added by Kevin Kennedy on March 25, 2014 at 9:22pm — 3 Comments

1963 390 oil pan

Anyone know the dimensions of a 1963 390 oil pan?

Added by Kevin Kennedy on March 16, 2014 at 11:03am — 1 Comment

dipstick tube

Does anyone have a dipstick tube for sale? '63 390 engine

Added by Kevin Kennedy on March 11, 2014 at 9:35pm — 1 Comment

ventalation gaskets

Does anyone now where I can get new gaskets for the A/C and heater ventilation system? Especially the big one that goes between the evaporator and duct work.

Added by Kevin Kennedy on September 28, 2013 at 11:14pm — 2 Comments


  • Add Photos
  • View All


Our 1963/64 Cadillac Chapter Store is Open!

Started by Jason Edge in Chapter Discussion. Last reply by Jason Edge 34 minutes ago. 2 Replies

Dave Leash, the CLC Sales & Marketing Rep,  has set up our own…Continue

Dash Lights

Started by Mark Borer in Restoration Discussion. Last reply by Tony Cassata 5 hours ago. 7 Replies

L+GJust went thru the dash compartment replacing all the burned out light bulbs.Everything is now working but am unhappy with the amount of light on the left side of the speedometer (compared to the…Continue

Transmisson Rebuild Time?

Started by Logan Robb in General Discussion. Last reply by Logan Robb 11 hours ago. 4 Replies

I've posted about this issue in the past and I thought I had it resolved. It would appear I do not as it has reared its ugly head again. My TH400 in the 64 Fleetwood has an intermittent problem of…Continue

Today's project, radiator overflow system

Started by Joe DiIaconi in General Discussion. Last reply by Kurt yesterday. 4 Replies

Installed a radiator overflow system. Could not have been simplerContinue

Blog Posts

Lower Front End Ball Joints

Posted by Logan Robb on May 11, 2023 at 9:04am 7 Comments

Good Morning all! 

I took the 64 into the shop to have some adjustments completed and in the process decided to have the lower ball joints replaced as was recommended the last time I had it in. I ordered the parts and came into the shop. They quoted me nearly $500 to replace those lower ball joints requiring nearly 4hrs of labor. Now this is a reputable shop and they know me by name here and they will continue to get my business. I am just questioning what on earth is…


1964 power steering sector rebuild

Posted by CHRIS CARLSON on March 20, 2023 at 11:32pm 3 Comments

 I'm having my steering sector rebuilt, and considering changing it from 20-1 ratio 4.2 turns lock to lock to 3.5 turns lock to lock @ 16-1 ratio, If i change from a 3 1/4" box to a 3" box i could have a 14-1 Ratio steering response would be faster, shorter distance to turn the wheel to get a response,   has anyone done this? and how do you like it? thank you

1964 Daville dashboard clock

Posted by Willem Bol on March 13, 2023 at 11:33am 2 Comments


Can somebody help me finding a dashboard clock  for my 1964 Cadillac DeVille Convertible?

Thank you in advance,

Willem Bol

The Netherlands

Does anyone know where I can get the bushings for AC compressor mount on the 429?

Posted by Robert Schles on February 21, 2023 at 11:45am 2 Comments

I've looked at the usual rubber sources but couldn't find any. 


  • Add Videos
  • View All

© 2023   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service