I mentioned during the 63/64 chapter zoom meeting on 3/21 that we had installed a car lift in our garage. Someone asked what kind and I didn't have the info at hand, so here is a link to it and also a link to some tall jack stands we use to add more stability to the car and an additional safety factor. There is something about getting underneath one of these cars that makes me a little nervous! 

DP10A Forward Lift

Ranger Under Hoist Stands

Here are some photos of the lift in action. The first photo shows the jack stands. My son and I have six cars we "play" with, plus our normal daily drivers... we should have installed this lift years ago!

Views: 949

Facebook Facebook

Comment

You need to be a member of 63/64 Cadillac Website to add comments!

Join 63/64 Cadillac Website

Comment by Les Eastling on March 23, 2021 at 9:13pm

Patrick... it is good to hear these are good lifts. My son used to own a body shop so he was pretty familiar with lifts, but he still did his research and came up with this one. You are right about raising it up and then lowering to the stops... the installers, the documents, and my son's experience made it very clear to operate it in that manner. I came from old school single post lifts and you would only go under once the safety pole engaged... and then you checked it to make sure it was locked in.

Comment by Patrick Westphal on March 23, 2021 at 6:16pm
Those are the type of lifts we have in the GM engineering centers all over GM. They work very well and are safe, just make sure that you use the raise the vehicle up to your working height and then lower it down to one of the stops on the lift before you do any work under the vehicle. Don't work under the vehicle if it is being held up by hydraulic pressure only.

Photos

  • Add Photos
  • View All

Forum

Add cruise control/Aftermarket Cruise control

Started by Logan Robb in 1963/64 Cadillac Specific Discussion. Last reply by Michael Vogler 4 hours ago. 13 Replies

Late in the evenings, I wonder about things I will probably never do as I am not that crazy. However, I know someone out there has tried it or wanted it bad enough they have done it. My 64 Fltwd did…Continue

Anyone Aware of a Raised Roof 75 Series?

Started by Jason Edge in General Discussion yesterday. 0 Replies

I received the email below and did not remember a raised roof 75 series but thought I would post here. Anyone know of or ever hear of this car?"I am a volunteer at Hillwood Museum and Gardens, the…Continue

Gump(Pat Westphal) you’re a gosh darn genius!

Started by Dave Fehrle in 1963/64 Cadillac Specific Discussion. Last reply by Patrick Westphal on Friday. 2 Replies

So I have been having problems with my brake lights. At first I thought it was both sides and turns out it is only the drivers side. Also, I thought the blinker worked and it didn’t and turned out…Continue

Front grill

Started by Phillip Hill in 1963/64 Cadillac Specific Discussion. Last reply by Dennis P. DiBari Jul 22. 11 Replies

Hi everyone im currently restoring my my front grill due to some previous clown painting it with silver frost paint and doing a dodgy job I would like to know what parts of the grill are anodised.it…Continue

Blog Posts

1963 RHS A/C kick panel - photos needed

Posted by SK on June 2, 2025 at 2:20pm 2 Comments

Could someone post front and back photos of the 1963 right-hand kick panel with A/C?

My car didn’t come with the original kick panels, so it's a bit of a mystery to me how I should cut the backing board and carpet to fit around the A/C.

Many thanks,

-Samu

Edelbrock Carb Block off Plates

Posted by Chase on March 12, 2025 at 2:05pm 14 Comments

Hey guys,

I have installed the same Edelbrock carb and have done everything the same as Jason’s carb and intake project. In the spring and summer months the car starts, runs and idles great! In the fall and winter months on a cold start, the car starts awful and wants to die until it warms up. I have to keep my foot on the throttle until it warms up or it will idle just terrible and try to die. Once it’s warm, it runs fantastic! Whats going on here? I was thinking of removing the…

Continue

'63 Tailfin Tales

Posted by Mark Mata on February 22, 2025 at 5:00pm 9 Comments

New old stock seat material

Posted by Ray Schick on August 22, 2024 at 6:25pm 2 Comments

I bought this seat material thinking that it’s…

Continue

Videos

  • Add Videos
  • View All

© 2025   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service