20 years ago I had a brake problem, got a life time master booster and cylinder from PepBoys and all was good. My wheel cylinders are all rebuilt with stainless steel sleeves and the springs, shoes and drums are all "new" (unworn, but over 10 years old). The pep boys master started to fail and I got it on exchange. It is from a 1968. So I had a 63 master and booster rebuilt and swapped them in today. Now I have nothing on the peddle and I am getting nothing out of the wheel cylinders with 20,40, 60 brake peddle strokes.
Any ideas what is wrong?? Massive amount of air? Any way to force brake fluid from the wheel cylinders??
I got nothin'
Tags:
My first thought is that the push rod is set incorrectly. It has to have the correct distance otherwise it will not move the floating piston to the correct position and open or close ports.
Check page 6-15 (1964 manual) on how to adjust the push rod.
When I did it on my car I took an old hotel key card and cut to specifications.
No idea why the pictures upside down. Maybe it is to help Kevin see them?
Anyways the first measurement is in inch and the other in millimeter. Choose what you need.
Pictures are ok down here.:-)
Because it was professionally rebuilt I would hope the setting is correct (maybe a bad assumption) I have an electric vacuum pump and I think I will start by a hard suck through the right rear wheel cylinder and see what happens. If this is not enough, I am thinking to prime the master manually and if that does not work - pull it off and start looking inside
Frank,
Did you bench bleed the new master cylinder? I've always done this on American MCs because without it they sometimes will pump only air and no fluid.
You need a couple short lengths of spare brake line. Attach them to the outlets and bend the end of each into the fluid in the reservoirs. With the MC clamped in a vice, push and release the piston until only fluid and no air bubbles are going into the reservoirs. I use a wooden dowell to avoid damage to the bore. This will prime it and hopefully solve your issue.
Come to think of it, since the MC is already mounted you can perform the procedure I described with it still there. Disconnect the lines, fit the bleeder lines and use the brake pedal to bleed.
Thank you - I think this is a great idea and likely the source of my issues!!
No, I did not even think about it. But I think what you are saying makes perfect sense
Started by Kurt in 1963/64 Cadillac Specific Discussion. Last reply by Patrick Westphal 22 hours ago. 16 Replies 4 Likes
Many owners have reported oil leaks at the rear main seal even after replacing the seal, myself included. Recently Tony Lentini found a Serviceman bulletin published in February 1965 which details a…Continue
Started by Michael Stinson in 1963/64 Cadillac Specific Discussion. Last reply by Bill Wolf yesterday. 9 Replies 0 Likes
Greetings Everyone. I read a discussion thread about "radiator and related", covering coolant overflow. Has anyone fitted an overflow reservoir / bottle to their 64 Cadillac? Is there if a…Continue
Started by Robert Dye in For Sale yesterday. 0 Replies 0 Likes
This is complete set of nice 63 Eldorado trim. Would like to sell as complete set but have duplicates of most of the moldings that can be sold separately. I am attaching a few pictures but you can…Continue
Started by Alan Clark in 1963/64 Cadillac Specific Discussion. Last reply by Alan Clark on Monday. 4 Replies 0 Likes
My car lacks the mechanism or spring needed to hold the jack in the storage slot on the right side of the trunk. Anyone have a picture of the item I should find?Continue
Posted by SK on June 2, 2025 at 2:20pm 2 Comments 0 Likes
Could someone post front and back photos of the 1963 right-hand kick panel with A/C?
My car didn’t come with the original kick panels, so it's a bit of a mystery to me how I should cut the backing board and carpet to fit around the A/C.
Many thanks,
-Samu
Posted by Chase on March 12, 2025 at 2:05pm 14 Comments 1 Like
Hey guys,
I have installed the same Edelbrock carb and have done everything the same as Jason’s carb and intake project. In the spring and summer months the car starts, runs and idles great! In the fall and winter months on a cold start, the car starts awful and wants to die until it warms up. I have to keep my foot on the throttle until it warms up or it will idle just terrible and try to die. Once it’s warm, it runs fantastic! Whats going on here? I was thinking of removing the…
ContinuePosted by Ray Schick on August 22, 2024 at 6:25pm 2 Comments 0 Likes
I bought this seat material thinking that it’s…
© 2025 Created by Jason Edge.
Powered by