Just wanted to check before removing my 1964 convertible top cylinders. I have the instructions from the 1964 shop manual. I have identified, in Red #s, the bolts in the procedure with the images. For those who have removed the cylinders please verify the accuracy of matching the procedure with the images.
Tags:
Hi there. I did this job about 6 years ago for my convertible removing the cylinders while I was replacing the top motor. You'll definitely want to mark off each bolt so you can line everything back up when putting it back together. I don't really recall if I actually followed that exact order of disassembly, but you might have to tilt the top back to get at some of the bolts easier if I remember correctly. I believe I skipped removing the #2 bolt.
Some tips: You will want some rag towels ready to catch the brake oil that comes out of the cylinders when you remove the hydraulic lines.
If you're replacing the top motor, most recommend that you replace the existing (yellow) brake fluid with transmission fluid. You'll have to compress the cylinders (if you're reusing them) by hand to drain out the fluid and I'd definitely recommend replacing the lines while you're doing this. If you're replacing both cylinders, lines, and the motor you can just add the fresh ATF.
That screw holding the cylinder in can be an absolute bear to get out. You'll have to muscle it out. I'd recommend putting the bracket and cylinder in a vice.
Don't forget some Loctite sealer on the tubes that screw into the cylinder when reassembling.
Best of luck and if you have any questions, I'll do what I can to help you out.
Chris,
I am replacing the motor, both cylinders, and all the hydraulic lines. The shop manual removal procedure has step 1: is to bring the top up and lock it to the windshield header. However, it sounds like you had to move the top to access some of the bolts?
Another question for you as a convertible owner is did you have your pinch-weld molding re-installed at any time on the car? Do you have a source for the clips as mine are rusty and old.
Thanks again for all your help!
Since I skipped removing bolt #2 that's probably why I needed to adjust the top. Go with the manual's directions and hopefully you won't have trouble accessing some of the bolts like I did.
I had the top replaced back around 2007, but I didn't do the install. I have no idea if they needed to remove the pinch-weld molding or not but it looked untampered with when I got the car back. I'm not quite sure where to source those clips, I'm sorry. Might talk to your local upholsterers as they probably will have the source for them.
I recently replaces the hydraulic system in a 63 convert. You may need to move the actuator mount blocks around to get to the mount bolt, but just follow the instructions as written. The shop manual is well written.
Glad to hear it went off without a hitch! I'm sure you'll have it back together in no time. Happy cruisin'!
Started by Logan Robb in 1963/64 Cadillac Specific Discussion. Last reply by Jason Edge 6 hours ago. 2 Replies 0 Likes
Not much of an Update and Questions: I was inspecting the top end and had removed the air cleaner in preparation to replace the intake. It was dirty so decided it needed a wipe down. My goof was…Continue
Started by Bill Wolf in 1963/64 Cadillac Specific Discussion. Last reply by Bill Wolf 7 hours ago. 4 Replies 0 Likes
The schematics are from the repair manual and show a LIGHT BLUE wire coming from the headlight switch to the dimmer switch. From the dimmer switch to the low beams on a TAN wire and to the high beams…Continue
Started by Michael Stinson in 1963/64 Cadillac Specific Discussion. Last reply by Jason Edge 18 hours ago. 2 Replies 0 Likes
My mechanic is having difficulty sourcing a front crankshaft seal. Can anyone recommend a replacement front crankshaft seal, and where to purchase? Amazon has a few that I think(?) are replacements…Continue
Tags: Seal, Crankshaft, Front
Started by Logan Robb in 1963/64 Cadillac Specific Discussion. Last reply by Michael Stinson yesterday. 3 Replies 0 Likes
When I get some new shoes for my 64 Fleetwood, I'd like to recondition the rims. I'd thought of getting them powder coated, and still plan to eventually, but the $700 quote I received shunted that…Continue
Posted by Chase on March 12, 2025 at 2:05pm 14 Comments 1 Like
Hey guys,
I have installed the same Edelbrock carb and have done everything the same as Jason’s carb and intake project. In the spring and summer months the car starts, runs and idles great! In the fall and winter months on a cold start, the car starts awful and wants to die until it warms up. I have to keep my foot on the throttle until it warms up or it will idle just terrible and try to die. Once it’s warm, it runs fantastic! Whats going on here? I was thinking of removing the…
ContinuePosted by Ray Schick on August 22, 2024 at 6:25pm 2 Comments 0 Likes
I bought this seat material thinking that it’s…
Posted by Dave Fehrle on March 23, 2024 at 3:23pm 8 Comments 1 Like
While checking my Carter carb with engine running, I took the air cleaner off and there was a very loud hissing sound of air. I placed a piece of paper over the carb and it didn’t move up or down, is this normal?
© 2025 Created by Jason Edge.
Powered by