Matti Roth's Discussions (129)

Discussions Replied To (112) Replies Latest Activity

"It does not really matter. From outside you see only the spring and the groove. When…"

Matti Roth replied Oct 7, 2022 to Heat riser and blocked intake manifold gasket

12 Oct 9, 2022
Reply by Jason Edge

"Hi Sammy in photo you see the throttle fully closed. The groove for the spring on to…"

Matti Roth replied Oct 6, 2022 to Heat riser and blocked intake manifold gasket

12 Oct 9, 2022
Reply by Jason Edge

"I removed radiator and AC condenser, and then it was possible to push from front and…"

Matti Roth replied Sep 15, 2022 to 429 restoration

78 Mar 8, 2023
Reply by Matti Roth

"I got engine and transmission in, and now lots of wires and hoses to connect. Now I…"

Matti Roth replied Sep 11, 2022 to 429 restoration

78 Mar 8, 2023
Reply by Matti Roth

"Getting there step by step. 429 travelled 30 miles to see the car and was coupled to…"

Matti Roth replied Sep 1, 2022 to 429 restoration

78 Mar 8, 2023
Reply by Matti Roth

"That is the right way, no rubber hoses."

Matti Roth replied Aug 23, 2022 to Transmission lines

11 Aug 27, 2022
Reply by Bill Hatfield

"Here is photo how the lines are attached in front of the block. I hope it helps. "

Matti Roth replied Aug 23, 2022 to Transmission lines

11 Aug 27, 2022
Reply by Bill Hatfield

"Upper port gives ported vacuum. Original carb gives intake vacuum which you get from…"

Matti Roth replied Aug 14, 2022 to Timing and carburetor

7 Aug 16, 2022
Reply by Sammy

"I plan to use Edelbrock 1406 from my 66 for 64 engine break in. It works fine now in…"

Matti Roth replied Aug 5, 2022 to 429 restoration

78 Mar 8, 2023
Reply by Matti Roth

"Should I get good compression results in cylinders when rotating engine manually slo…"

Matti Roth replied Aug 4, 2022 to 429 restoration

78 Mar 8, 2023
Reply by Matti Roth

RSS

Photos

  • Add Photos
  • View All

Forum

Clock Removal

Started by Jeff Donaldson in General Discussion. Last reply by Jason Edge 18 hours ago. 2 Replies

Hello Everyone,I tried to remove my clock today and couldn't seem to get it to rotate more than a 16th to an 8th of an inch. I followed the instuctions in the manual (counterclockwise approximately…Continue

Dino Diaries - All Jacked Up For Christmas!

Started by Jason Edge in General Discussion yesterday. 0 Replies

I have very limited space in my 3 bay garage with the left and right bay used for storage and work tables, etc leaving the narrow center aisle for my 1964 Coupe de Ville Dino. Six years ago I bought…Continue

Power Brake Booster

Started by Stephen Pechenik in General Discussion. Last reply by Bill Wolf yesterday. 13 Replies

Hello Co-Members,I recently purchased a  low mileage1963 Sedan Deville Park Avenue.  It is extremely solid and runs well.  Neverthelss, it has minor problems that need to be addressed before I can…Continue

Body side molding install help needed

Started by Wayne Morris in 1963/64 Cadillac Specific Discussion. Last reply by Wayne Morris on Saturday. 6 Replies

I am in the process of trying to install body side molding. I have completed installing the two front fender pieces and now trying ti figure out the rest.…Continue

Blog Posts

New old stock seat material

Posted by Ray Schick on August 22, 2024 at 6:25pm 2 Comments

I bought this seat material thinking that it’s…

Continue

Loud air moving sound within carb with cleaner removed

Posted by Dave Fehrle on March 23, 2024 at 3:23pm 8 Comments

While checking my Carter carb with engine running, I took the air cleaner off and there was a very loud hissing sound of air. I placed a piece of paper over the carb and it didn’t move up or down, is this normal?

Vintage Air AC

Posted by Chase on March 21, 2024 at 5:55am 0 Comments

Hey everyone, has anybody done a Vintage Air AC/Heat setup in their car? I want to bypass the old vacuum setup and go with a Vintage Air Gen 2 model. Before I get started, does anyone have any experience with this? (Which model to go with, do’s and dont’s, etc.) It looks pretty involved. Any and all info/pics would be greatly appreciated. Thanks!

accumulator dryer

Posted by CHRIS CARLSON on December 6, 2023 at 10:54am 0 Comments

Who rebuilds original AC  accumulator dryers for 1964 Cadillac? I have been on Classic auto air in Tampa FL wait list for over a year ,  There is one on Old air products web site that looks very similar to the original # 21-4214A but states it fits 1962 Gm cars, The one recommended for a 1964 Cadillac is half the length 21-4215A    What  is everyone using ? I would prefer to be as original as possible. Thanks

Events

Videos

  • Add Videos
  • View All

© 2024   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service