Hi

The original color of my 1963 Eldorado is Frost Silver. I can find the PPG and Dupont paint codes from the web, but at least here in Europe paint shops are not able to mix paint with those old codes.

Could you advise me: are you able to mix the orginal colors in the USA or does someone know a modern reference color? I know that one option would be to use the paint chart chips, but I have not seen a chart which would have had the fire-frost chips.

My car was repainted probably in the early 1980s, so there is not that much fire or frost left anymore. Therefore I’d be interested to know what is the speciality with these colors? Is it just a metal color with larger flakes than normally used in 1963 or is it some kind of pearl(ish) paint?

The 1963 Data book description is ”Fire-Frost is a recently developed bright flaked pigment that creates an unusually high iridescent radiance. Extremely thin flakes, but of a larger size than any previously used in metalliferous finishes, are homogenized with the basic acrylic lacquer. The light reflections from the many diamond-like facets of these particles produce amazing beauty and lustre.”

Thanks

Samu

Views: 42

Reply to This

Replies to This Discussion

Samu,

Mixing the old color codes with modern paint is done quite easily here. Check this place out: https://www.autocolorlibrary.com

I have not used them but they showed up when I searched and it certainly seems like they would be very capable.

Many thanks Ian. It certainly looks that Autocolorlibrary would be able to mix the paint.

RSS

Photos

  • Add Photos
  • View All

Forum

Current 1963/64 Cadillac Listings on eBay

Started by Jason Edge in For Sale. Last reply by Jason Edge 3 hours ago. 1 Reply

To see all 1963/64 Cadillacs Listed on eBay in the USA…Continue

Tags: ebay

Happy Father's Day!

Started by Jason Edge in 1963/64 Cadillac Specific Discussion. Last reply by Tony and Ginny 429 16 hours ago. 1 Reply

Happy Father's Day to my dad, Sam Edge. He was there in the beginning with…Continue

622 nss 63 tilt

Started by Kim K Kaiser in 1963/64 Cadillac Specific Discussion. Last reply by Tony and Ginny 429 yesterday. 7 Replies

Previously, i mentioned the  bu lights didnt work, and conversatiin went to nss.   Mine has the two jumped wire bypass so car will go in drive/start.Got the switch out and the outer tract plastic is…Continue

Timing chain help

Started by Cody in 1963/64 Cadillac Specific Discussion. Last reply by Tony and Ginny 429 on Saturday. 3 Replies

I have the front of my engine taken apart to replace the timing chain and gears. According to the manual it says to remove the cam gear and chain together then the crank gear.I can’t for the life of…Continue

Blog Posts

New vehicle in the club

Posted by Patrick Westphal on June 17, 2021 at 4:00pm 1 Comment

I was successful in getting a vehicle from the New York contact I talked about at the last club meeting. I am still trying to figure out how to post a picture of the vehicle that is tied with this comment so if you see a random picture of a black convertible in a yard, that's me haha.  …

Continue

Torque converter grab when idling in Drive

Posted by Cliff Johnston on June 14, 2021 at 8:47pm 2 Comments

Hi Everyone, been quite a while since i have been on here.

I have had an issue with the idle on my 64 Coupe Deville ever since i have had it.

With the Idle set high enough that it is smooth, but still a nice idle, the RPM seems only slightly too high for the stall of the Torque Converter. And therefore it tends to sit there and grab and lunge a bit. So until now, i have been putting the car in Neutral at the lights to stop this happening.

I've had the car dyno tuned and…

Continue

Can you help? Driveshaft Question....

Posted by Chris on May 30, 2021 at 8:55am 1 Comment

Hello!

Newbie to the group here - we have already found tons of invaluable information on the board, so thanks! We are restoring a 1963 Series 62 Convertible. We are wondering if anyone knows of a source to buy the propellor yoke flange (that bolts to the pinion flange) for the driveshaft? One of our ears partially broke off. Not sure if we can buy just the yoke flange as an aftermarket part, or if it has to be rebuilt by a welder/fab guy? Maybe a salvage yard for a source? Again, any…

Continue

Thank you Kurt re: VIN location

Posted by Robert Pellow on April 19, 2021 at 1:07pm 0 Comments

I just wanted to say a thank you to Kurt for steering me to the tech tips page on V.I.N. locations.  Excellent information.  Thanks a bundle.

Robert Pellow

Videos

  • Add Videos
  • View All

© 2021   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service