64 Convertible Parts
Hello
Does anyone know who would have a
1) "Top Boot Slide Rail" for my convertible top boot.
2) Driver side solid Fender Trim
I asked Jason and Russ and neither one has one. Any help would be appreciated.
Thanks
Dominic
Replies to This Discussion
-
Permalink Reply by Dennis P. DiBari on
-
Hi Dominic,
I just replaced my passenger side fender trim. Mine is 65 3/4" long; it's a 1964 Series 62. I searched everywhere for a year and finally got it from CPR (Cadillac Parts and Restoration). He is great and runs the CLC 59-60 Chapter. He is in Poughkeepsie, NY. His name is Frank Nicodemus. Even got the clips from him. He'll remember me, as he did some work on my steering column/horn.
Dennis DiBari, Cottekill, NY
Your convertible is great!
-
Permalink Reply by Dominic Salemi on
-
Dennis
Thank you and I also found one on JEGS but not sure it is the correct part. The picture shows correct part but you know how that could go.
Thank you
Dominic
-
-
OK Dom. Keep CPR as a good resource, being you are also in NY.
Dennis
Members
Forum
Logans Intake Project, 1964 Fleetwood, Progress Report #2
Started by Logan Robb in 1963/64 Cadillac Specific Discussion 2 minutes ago. 0 Replies 0 Likes
Hello all!Just a short update this evening!I wrestled with the exhaust manifold studs and ultimately chickened out on replacing all 4 of the studs. I only replaced the stud that I spun the threads…Continue
Scout Shows up in the Garage with "Man Bun" to Work on Cadillac!
Started by Jason Edge in General Discussion. Last reply by Dennis P. DiBari 4 hours ago. 1 Reply 0 Likes
Cheryl brought my 4 1/2 month old boy Scout out to the garage in a man-bun to help work on the Cadillac. Sometimes you just have to roll with it! (I am scared to see who she will "dress up" Bandit…Continue
Logans Intake Project, 1964 Fleetwood, Progress Report #1
Started by Logan Robb in 1963/64 Cadillac Specific Discussion. Last reply by Logan Robb 12 hours ago. 5 Replies 0 Likes
I plan to do a full write up when this project is complete, however, I figured someone may get some benefit of seeing the progressions I make and the steps I took to get there. This also is a good…Continue
Rear main seal
Started by Phillip Hill in 1963/64 Cadillac Specific Discussion. Last reply by Phillip Hill yesterday. 4 Replies 0 Likes
Hi Everyone can somebody tell me where I can get a reliable rear main seal?I have done the end cap modification and replaced the seal twice,after around 500 miles it starts to leak again,not as bad…Continue
Blog Posts
Edelbrock Carb Block off Plates
Posted by Chase on March 12, 2025 at 2:05pm 14 Comments 1 Like
Hey guys,
I have installed the same Edelbrock carb and have done everything the same as Jason’s carb and intake project. In the spring and summer months the car starts, runs and idles great! In the fall and winter months on a cold start, the car starts awful and wants to die until it warms up. I have to keep my foot on the throttle until it warms up or it will idle just terrible and try to die. Once it’s warm, it runs fantastic! Whats going on here? I was thinking of removing the…
ContinueNew old stock seat material
Posted by Ray Schick on August 22, 2024 at 6:25pm 2 Comments 0 Likes
I bought this seat material thinking that it’s…
Loud air moving sound within carb with cleaner removed
Posted by Dave Fehrle on March 23, 2024 at 3:23pm 8 Comments 1 Like
While checking my Carter carb with engine running, I took the air cleaner off and there was a very loud hissing sound of air. I placed a piece of paper over the carb and it didn’t move up or down, is this normal?
Events
© 2025 Created by Jason Edge.
Powered by
