Brakes on the 64 Fleetwood need some attention.
It stops and is perfectly safe, but they lack the confidence I'd like to have.
I've replaced the wheel cylinders, springs, rubber brake hose, and shoes, and backing plate. I did re use the old drums and I've only worked on the front brakes for the time being.
If the drums can't be turned for some reason, what aftermarket drums have any of you had luck with? I also have new bearings and seals to go in as well but haven't taken that project on yet.
Any other parts that I should be looking to replace in the front brake area?
Thanks all!
Tags:
Mr. Robb,
Most comments on after-market drums here and on other forums have been very negative. A general consensus seems to be that sourcing original drums which can still be re-surfaced is the best solution. See, for example:
https://6364cadillac.ning.com/forum/topics/64-caddie-brake-drums?pa...
I don't know if Mr. Edge still has any in inventory. If not, you may wish to check about his waiting list.
Somewhere I may still have a link to a small North American company which was casting and making quality replacement drums. I'll see if I can find it.
You could always pull your back drums and check to see if they are candidates for re-surfacing.
"(S)pecs for the drums are in the Shop Manual. For the drums I deal with, the spec 12.060 inch diameter". Jason Edge at
https://forums.cadillaclasalleclub.org/index.php?topic=156835.0
Mr. Russ Austin may also have good used OEM drums.
Thank you! I’d seen some of the issues for quality drums. I’ll have to have them measured when it goes in for brake work.
I certainly don’t feel the need to change over to disc. I just need to get the drums in tip too shape! I appreciate the insight in Raybestos.
The new reman drums are junk. Either the adjuster hole is missing, drum is too far out of round to turn true, or the balancing weights interfere with the wheel being installed.
I do have 2 front original drums that have been turned, and 1 rear turned ready to go. I can get more turned as well.
Please email me at russ@thecadishack.com if you want to inquire about them.
Unless subject to some harsh condition (e.g. outside in the weather with heavy corrosion, harsh breaking resulting in excessive or uneven wear, or physical damage to the drum causing it to warp) most drums can be turned. These are thick drums with a lot of meat on them. If yours turns freely and none of the above issues just have your machine ship turn yours. I have several sets of rear drums only, or front drum & hubs, both unturned as pulled and turned. You can see them by going to my Facebook Parts Page at https://www.facebook.com/ClassicCadillacParts/photos, click Albums, see all and scroll down a few pages.
Click Here for a direct link to the drums only.
If you want to pull the trigger for any of my drums email me with your shipping address to jasonedge64@outlook.com
Started by Kevin Wray in Restoration Discussion. Last reply by Jason Edge yesterday. 6 Replies 1 Like
Thanks to Jason's expert advice, I was able to remove the fender trim on my 63 de Ville without removing the fender. Pics contain the locations of the 3/8 in nuts and how to access them. My clips…Continue
Started by Wayne Morris in 1963/64 Cadillac Specific Discussion. Last reply by Jason Edge yesterday. 3 Replies 0 Likes
I am in the process of trying to install body side molding. I have completed installing the two front fender pieces and now trying ti figure out the rest.…Continue
Started by David Erickson in General Discussion yesterday. 0 Replies 0 Likes
I have an all original 63 Cadillac Park Avenue. It has won awards in the past in the Originality Category. My question to the group is what types of work you can do on the car that does not cause…Continue
Started by Jason Edge in 1963/64 Cadillac Specific Discussion. Last reply by Jason Edge on Wednesday. 1 Reply 5 Likes
To see all 1963/64 Cadillacs Listed on eBay in the USA…Continue
Tags: ebay
Posted by Ray Schick on August 22, 2024 at 6:25pm 2 Comments 0 Likes
I bought this seat material thinking that it’s…
ContinuePosted by Dave Fehrle on March 23, 2024 at 3:23pm 8 Comments 1 Like
While checking my Carter carb with engine running, I took the air cleaner off and there was a very loud hissing sound of air. I placed a piece of paper over the carb and it didn’t move up or down, is this normal?
Posted by Chase on March 21, 2024 at 5:55am 0 Comments 1 Like
Hey everyone, has anybody done a Vintage Air AC/Heat setup in their car? I want to bypass the old vacuum setup and go with a Vintage Air Gen 2 model. Before I get started, does anyone have any experience with this? (Which model to go with, do’s and dont’s, etc.) It looks pretty involved. Any and all info/pics would be greatly appreciated. Thanks!
Posted by CHRIS CARLSON on December 6, 2023 at 10:54am 0 Comments 0 Likes
Who rebuilds original AC accumulator dryers for 1964 Cadillac? I have been on Classic auto air in Tampa FL wait list for over a year , There is one on Old air products web site that looks very similar to the original # 21-4214A but states it fits 1962 Gm cars, The one recommended for a 1964 Cadillac is half the length 21-4215A What is everyone using ? I would prefer to be as original as possible. Thanks
December 15, 2024 from 7pm to 8:30pm – Zoom
0 Comments 0 Likes© 2024 Created by Jason Edge. Powered by