Hello, I now own my grandfather's '64 Sedan DeVille with a 490ci Carter 3903S carburetor. My more mechanically-inclined friend and I are troubleshooting some carburetion issues that came up. In 2016, we rebuilt the carburetor with an AutoZone GP Sorenson Carburetor Kit 96-568 (https://www.autozone.com/fuel-delivery/carburetor-kit/p/gp-sorensen...) with improved carburetion results at that time. The link has a picture that is more clear than the image I was going to attach. At that time, we left the gasket (which we now know was a Fel-Pro 60034) that was touching the intake manifold alone. Replaced all other gaskets with what we believed to be correct from the kit. 

Recently, we decided to rebuild it again for a number of reasons (starting that required 5-6 pedal pumps to prime, reduced power, bogging on quick acceleration from dead-stop) with a Mike's Carburetor Kit K4011 (https://www.carburetor-parts.com/k4011.html

After reading Jason Edge's post from here, he states "For the Carter AFB I sell the Fel Pro 60034. It takes 2 of these gaskets, one below and one above the insulator." 

Neither of these two Carter labeled carburetor rebuild kits include the 60034 style gasket. Jason's pictures comparing the Carter to the Rochester show two differences. Here is the 60034 carter. Red ink shows the areas that are missing from Rochester.

My friend and I are very confused and initially believed that the kits we bought were correct but according to Jason Edge the gaskets those two suppliers include are not for THIS Carter apparently.

Can anyone provide some insight or direction as to who is correct? If Jason is correct then we should be following this pattern:

Intake Manifold --> 60034 gasket --> insulator spacer --> 60034 gasket --> metal shim --> carburetor

Thank you,

ROB

Facebook Facebook

Views: 417

Reply to This

Replies to This Discussion

Carter gasket is FelPro 60034
Rochester gasket is FelPro 9770.
See pictures below.
You will need 2 gasket as one is above and one below the intake to carb insulator.
If you cannot find them I sell them new in pairs for $15.

Here are pictures of both types of gaskets:

Thank you Jason and Tony/Ginny for your replies. We found the 60034 gasket  through Napa Auto Parts. I just don’t get why the “Carter” labeled kits from those two suppliers wouldn’t include them 

Someone just obviously mixed things up when they were putting the kit together. Other than the many gaskets I have seen first hand from the 56 and counting parts cars, is the fact the Rochester listed FelPro gasket says it replaces 147 7371 on the packaging and looking at the Cadillac Master Parts book, that is the original # they list for the Rochester with the Carter having a different #.  To me that is a double check confirmation of which is which.   Also, just for reference the original Carter gasket was part # 147 7370. 

I think I’ll contact Mike’s Carburetor and let them know of the issue with our Carter’s. Great. Thank you for that info Jason. I find that detailed info like this is so valuable. 

RSS

Photos

  • Add Photos
  • View All

Forum

Rear main seal

Started by Phillip Hill in 1963/64 Cadillac Specific Discussion. Last reply by Phillip Hill 11 hours ago. 4 Replies

Hi Everyone can somebody tell me where I can get a reliable rear main seal?I have done the end cap modification and replaced the seal twice,after around 500 miles it starts to leak again,not as bad…Continue

Logans Intake Project, 1964 Fleetwood, Progress Report #1

Started by Logan Robb in 1963/64 Cadillac Specific Discussion. Last reply by Logan Robb yesterday. 3 Replies

I plan to do a full write up when this project is complete, however, I figured someone may get some benefit of seeing the progressions I make and the steps I took to get there. This also is a good…Continue

1963 Cadillac differential 3.25

Started by Frank Murch in 1963/64 Cadillac Specific Discussion. Last reply by Frank Murch on Thursday. 2 Replies

I have a 1963 Cadillac differential with 80K on it. Found a limited slip a while back, and I do not think I will ever used the original diff.  In is in carlsbad California 92009.  Let me know if you…Continue

headlight / dimmer switch confusion (63 Sedan Deville)

Started by Bill Wolf in 1963/64 Cadillac Specific Discussion. Last reply by Jason Edge on Thursday. 3 Replies

The schematics are from the repair manual and show a LIGHT BLUE wire coming from the headlight switch to the dimmer switch. From the dimmer switch to the low beams on a TAN wire and to the high beams…Continue

Blog Posts

Edelbrock Carb Block off Plates

Posted by Chase on March 12, 2025 at 2:05pm 14 Comments

Hey guys,

I have installed the same Edelbrock carb and have done everything the same as Jason’s carb and intake project. In the spring and summer months the car starts, runs and idles great! In the fall and winter months on a cold start, the car starts awful and wants to die until it warms up. I have to keep my foot on the throttle until it warms up or it will idle just terrible and try to die. Once it’s warm, it runs fantastic! Whats going on here? I was thinking of removing the…

Continue

'63 Tailfin Tales

Posted by Mark Mata on February 22, 2025 at 5:00pm 9 Comments

New old stock seat material

Posted by Ray Schick on August 22, 2024 at 6:25pm 2 Comments

I bought this seat material thinking that it’s…

Continue

Loud air moving sound within carb with cleaner removed

Posted by Dave Fehrle on March 23, 2024 at 3:23pm 8 Comments

While checking my Carter carb with engine running, I took the air cleaner off and there was a very loud hissing sound of air. I placed a piece of paper over the carb and it didn’t move up or down, is this normal?

Videos

  • Add Videos
  • View All

© 2025   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service