Neither of my cornering lights are working. I started by focusing on drivers side. I removed the entire assembly and cleaned it up, replaced the wire to the socket, cleaned and lubricated the socket and spring. Made sure light now worked by attaching directly to battery terminals. Reinstalled assembly and plugged it back in and no work. Attached a separate ground directly to the battery terminal and still no work. I checked orange power wire coming in and no power. I have the ignition turned on, signal on, headlights on and still no power to orange wire. Everything working but the corner light. Passenger side does not work either but have not done anything on that side yet. Figure one side at a time. Where should I look next. I have a manual. Thanks Larry
Tags:
Thats all you will get with just the top clamp removed. There is a bottom clam as well. Be farefull to not damage the steering rag joint.
Loosened off the two bottom bolts at steering column base clamp and the two bottom floor bolt which dropped column enough to get the job done. Once again thanks to all for the tips and guidance. Larry
Congrats on the fix! ps. I have been staring at an outer T-3 headlamp on that last parts car still up on the car hauler. If it works and you still need one it has your name on it.
If he doesn't want it, I would be interested.
Tony, Larry had been waiting a long time for good outer T3 and was next up on the Wait List. I have one other Chapter member on the list after Larry, so you would be #2 in line after Larry gets this one. I assume you need one outer T3.
I do have 6 tested inner Hi Beam T3's for you or anyone that needs that T3 headlamp.
Thank you Jason. I ended up ordering one from Russ.
That is great. They are getting harder and harder to find. If anyone else needs the inner hi beams I have 6 and they are $15 each for Chapter Members.
Started by Patrick Westphal in For Sale. Last reply by Jason Edge on Monday. 1 Reply 0 Likes
Hey everyone,I have a set of front bumpers, both ends and the center section, that I am looking to sell. If you are looking for these contact me and we will talk about it. …Continue
Started by Norman Silverman in 1963/64 Cadillac Specific Discussion. Last reply by Norman Silverman on Sunday. 5 Replies 0 Likes
Hello AllI am thinking about replacing the shocks on my 64 SDV. I want to do so with units that are closest to what was originally in the car in so far as ride quality. I believe these were gas…Continue
Started by Jason Edge in 1963/64 Cadillac Specific Discussion. Last reply by Dennis P. DiBari on Sunday. 1 Reply 0 Likes
Last night I was installing the freshly cad plated inner fender to frame rear support brace rods and remembered how this has been often missing on the many parts cars I have brought in. The thing is…Continue
Started by Michael Monson in 1963/64 Cadillac Specific Discussion. Last reply by Jason Edge on Sunday. 2 Replies 0 Likes
I'm currently rounding up parts for a heater core replacement in my 1964 Deville. I'm looking for replacement hoses that connect to the heater core itself. It's a factory a/c car and has the metal…Continue
Posted by SK on June 2, 2025 at 2:20pm 2 Comments 0 Likes
Could someone post front and back photos of the 1963 right-hand kick panel with A/C?
My car didn’t come with the original kick panels, so it's a bit of a mystery to me how I should cut the backing board and carpet to fit around the A/C.
Many thanks,
-Samu
Posted by Chase on March 12, 2025 at 2:05pm 14 Comments 1 Like
Hey guys,
I have installed the same Edelbrock carb and have done everything the same as Jason’s carb and intake project. In the spring and summer months the car starts, runs and idles great! In the fall and winter months on a cold start, the car starts awful and wants to die until it warms up. I have to keep my foot on the throttle until it warms up or it will idle just terrible and try to die. Once it’s warm, it runs fantastic! Whats going on here? I was thinking of removing the…
ContinuePosted by Ray Schick on August 22, 2024 at 6:25pm 2 Comments 0 Likes
I bought this seat material thinking that it’s…
© 2025 Created by Jason Edge.
Powered by