Dino Diaries - July 5, 2025 - Cad Plated Trans Linkage Installed

My '64 Coupe de Ville Dino has been sitting up on the 12" wheel cribs forever waiting for me to slide back under it and tackle some cleaning, painting and replacing some of the hardware with cadmium plated goodies as I go along. Between the Grand National and many house projects I have been putting everything off, however I finally pulled the trigger, slide back under and started with replacing the transmission linkage assembly which bolts to the left frame rail.  See picture below.

I have a trunk load of cad plated goodies and will start installing as it makes sense.  I will report on other projects later but thought I would share some undercarriage bling.

If you have a 1964 Cadillac with the Turbo HydraMatic transmission (deVilles and Fleetwoods) I have several of these transmission linkage sets available for $80 which drops to $60 with Chapter discount. That is a lot of cad plated hardware for $60 and takes me considerable time to put the sets together. 

Ok...here are the pics: 

Facebook Facebook

Views: 27

Reply to This

Replies to This Discussion

Here is a picture of sets I have put together:

RSS

Photos

  • Add Photos
  • View All

Forum

Dino Diaries - July 11, 2025 - Busted!

Started by Jason Edge in General Discussion. Last reply by Jason Edge 5 hours ago. 4 Replies

So I am starting to crawl around under Dino seeing what I can fix or upgrade and as I was putting the trans linkage in a few nights ago, the rear trans mount caught my eye. I remembered that these 64…Continue

Bleeding brakes

Started by Dave Fehrle in 1963/64 Cadillac Specific Discussion. Last reply by Russ Austin on Thursday. 3 Replies

I have finished replacing all the rear suspension and am at the last item, which is bleeding the rear brakes. I am using the Jason Edge vacuum pump method and all went well with the rear passenger…Continue

Front grill

Started by Phillip Hill in 1963/64 Cadillac Specific Discussion. Last reply by Dennis P. DiBari on Wednesday. 8 Replies

Hi everyone im currently restoring my my front grill due to some previous clown painting it with silver frost paint and doing a dodgy job I would like to know what parts of the grill are anodised.it…Continue

Getting hot when going fast…

Started by Mack in 1963/64 Cadillac Specific Discussion. Last reply by Dennis P. DiBari on Tuesday. 6 Replies

So… I do have a few of 63 Coupes, all have same setup with carbs, Pertronix, shroud, new US Radiator radiators etc … but only one of them gets a bit hot when I am hauling faster than 60mph and car…Continue

Blog Posts

1963 RHS A/C kick panel - photos needed

Posted by SK on June 2, 2025 at 2:20pm 2 Comments

Could someone post front and back photos of the 1963 right-hand kick panel with A/C?

My car didn’t come with the original kick panels, so it's a bit of a mystery to me how I should cut the backing board and carpet to fit around the A/C.

Many thanks,

-Samu

Edelbrock Carb Block off Plates

Posted by Chase on March 12, 2025 at 2:05pm 14 Comments

Hey guys,

I have installed the same Edelbrock carb and have done everything the same as Jason’s carb and intake project. In the spring and summer months the car starts, runs and idles great! In the fall and winter months on a cold start, the car starts awful and wants to die until it warms up. I have to keep my foot on the throttle until it warms up or it will idle just terrible and try to die. Once it’s warm, it runs fantastic! Whats going on here? I was thinking of removing the…

Continue

'63 Tailfin Tales

Posted by Mark Mata on February 22, 2025 at 5:00pm 9 Comments

New old stock seat material

Posted by Ray Schick on August 22, 2024 at 6:25pm 2 Comments

I bought this seat material thinking that it’s…

Continue

Videos

  • Add Videos
  • View All

© 2025   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service