Dino Wiper Swap
Yesterday I finally pulled my already very nice windshield wiper motor and washer pump assembly in my 64 Coupe de Ville 'Dino', to replace with a rebuilt unit I have had a couple of years and recorded a quick video before removing. Here is that video clip testing the one I removed, then a picture of the rebuilt one installed. Both were very nice motor/washer pump assembles. The old one went shipped out to a Chapter Member today.
Replies to This Discussion
-
Permalink Reply by Logan Robb on
-
Great video. Wondering if you could post a pic of the actual nozzles on the cowl? This is a future project on my 64 Fltwd and would like to come back to this thread.
-
Permalink Reply by Jason Edge on
-
Logan, Are yours missing? If so, I have plenty of the washer jet and nozzles as seen below for $10 each side. Email me at jasonedge64@outlook.com.
-
-
Based off of the photo, I suppose mine are not missing. I thought there to be some piece that connects to the end of the jet there. With the eye, it looks like it would shoot off to the side, not onto the w/s.
-Logan
Members
Forum
Front door handle lights not working
Started by Bill Wolf in 1963/64 Cadillac Specific Discussion. Last reply by Kurt yesterday. 1 Reply 0 Likes
My front door handle lights would not go on when I opened the doors. Bulbs were good and had power to them. Was not getting a ground. The door switch was corroded and wasn't making contact when the…Continue
lighted headlight switch
Started by Bill Wolf in 1963/64 Cadillac Specific Discussion. Last reply by Bill Wolf on Saturday. 2 Replies 1 Like
I had to replace the heater core in my 63 SDV, so I decided to replace all the dash lights with LED's. and replaced all the vacuum lines. While I was in there, I added a light to the headlight switch…Continue
Rear suspension project
Started by Dave Fehrle in 1963/64 Cadillac Specific Discussion. Last reply by Robert Alan Shannon on Tuesday. 9 Replies 0 Likes
I’m starting the complete rear suspension update/upgrade-new springs and shocks,replacing spherical joint and bushings on yoke and control links! Just wondering if there are any tips to help with the…Continue
TV rod adjustment 1963 Cad
Started by Mark Geertsma in 1963/64 Cadillac Specific Discussion. Last reply by Russ Austin May 12. 4 Replies 0 Likes
I’m struggling with my TV rod adjustment. I’ve been trying to adjust it as per shop manual, but it’s still not OK. When cold, it shifts smoothly through all four gears, when hot, it hesitates (lots…Continue
Tags: adjustment, rod, TV
Blog Posts
Edelbrock Carb Block off Plates
Posted by Chase on March 12, 2025 at 2:05pm 14 Comments 1 Like
Hey guys,
I have installed the same Edelbrock carb and have done everything the same as Jason’s carb and intake project. In the spring and summer months the car starts, runs and idles great! In the fall and winter months on a cold start, the car starts awful and wants to die until it warms up. I have to keep my foot on the throttle until it warms up or it will idle just terrible and try to die. Once it’s warm, it runs fantastic! Whats going on here? I was thinking of removing the…
ContinueNew old stock seat material
Posted by Ray Schick on August 22, 2024 at 6:25pm 2 Comments 0 Likes
I bought this seat material thinking that it’s…
Loud air moving sound within carb with cleaner removed
Posted by Dave Fehrle on March 23, 2024 at 3:23pm 8 Comments 1 Like
While checking my Carter carb with engine running, I took the air cleaner off and there was a very loud hissing sound of air. I placed a piece of paper over the carb and it didn’t move up or down, is this normal?
Events
© 2025 Created by Jason Edge.
Powered by
