A few questions on the resistor wire, what color is it in the pic? The yellow/blue or black? And connecting to the ACC on the fuse box seems easiest way to go with the new switched wire, but where can I get a connector for the ACC?
Tags:
Hi Dave,
I have never seen a fuel line twisted like that. Pretty sure the gas flow is quite restricted. Any chance to run a new fuel line from the fuel pump to the carb.?
Dennis DiBari
Dave,
If you get new fuel line and a good flaring kit, you can run a new line to the carburetor. You can use the fittings you already have and put them on the line before you flare both ends. The gas flow will be correct.
Dennis
Tabs in red are not interlocked. If you want a better fuel line I have a nice original fuel filter to Carter AFB carb line I just pulled from the last parts car. Price is $25, which drops to $18.75 with Chapter Discount and can ship for $10 for a final total of $28.75. Shoot me an email if interested.
Dave, Have you been able to get your ignition system operating properly? I think that you are wired into the wrong circuit for 12 volt power. I would be glad to get on a call with you to discuss it if you would like that.
Pat, that would be great as I will take any and all help getting this beast back in running mode! I sent a friend request, then i can send you my number.
I wanted give an update on pertronix 3 installation.
It is now working but it was not a straight line install and then running! Originally I used the ACC for the switched 12 volt with no success. Then I cleaned up the fuse holders for the ACC and got 12 volts to the end of the wire. But it still wouldnt start and in stepped Pat Westphal!! He suggested tapping i to an ‘ignition’ line, either the pink wire that the resistor wire is connected to or using the tan/white wire that runs into the wiper motor in the engine bay. It is definitely an easier access point, so i used it.
In the meantime, i was waiting for a fuel line from Jason Edge from filter to carb. Of course, during the install i cross thread into the filter-“&$:&!?$& were the exact words used! Luckily, it was the female connector on the filter that cross threaded and you tube had a nice fix and it worked. So installed all fuel lines, and fired it up and started right up!!
Again big shout out to Pat and Jason for all the help and willingness to share their knowledge!
Started by Kevin Wray in Restoration Discussion. Last reply by Jason Edge yesterday. 6 Replies 1 Like
Thanks to Jason's expert advice, I was able to remove the fender trim on my 63 de Ville without removing the fender. Pics contain the locations of the 3/8 in nuts and how to access them. My clips…Continue
Started by Wayne Morris in 1963/64 Cadillac Specific Discussion. Last reply by Jason Edge yesterday. 3 Replies 0 Likes
I am in the process of trying to install body side molding. I have completed installing the two front fender pieces and now trying ti figure out the rest.…Continue
Started by David Erickson in General Discussion yesterday. 0 Replies 0 Likes
I have an all original 63 Cadillac Park Avenue. It has won awards in the past in the Originality Category. My question to the group is what types of work you can do on the car that does not cause…Continue
Started by Jason Edge in 1963/64 Cadillac Specific Discussion. Last reply by Jason Edge on Wednesday. 1 Reply 5 Likes
To see all 1963/64 Cadillacs Listed on eBay in the USA…Continue
Tags: ebay
Posted by Ray Schick on August 22, 2024 at 6:25pm 2 Comments 0 Likes
I bought this seat material thinking that it’s…
ContinuePosted by Dave Fehrle on March 23, 2024 at 3:23pm 8 Comments 1 Like
While checking my Carter carb with engine running, I took the air cleaner off and there was a very loud hissing sound of air. I placed a piece of paper over the carb and it didn’t move up or down, is this normal?
Posted by Chase on March 21, 2024 at 5:55am 0 Comments 1 Like
Hey everyone, has anybody done a Vintage Air AC/Heat setup in their car? I want to bypass the old vacuum setup and go with a Vintage Air Gen 2 model. Before I get started, does anyone have any experience with this? (Which model to go with, do’s and dont’s, etc.) It looks pretty involved. Any and all info/pics would be greatly appreciated. Thanks!
Posted by CHRIS CARLSON on December 6, 2023 at 10:54am 0 Comments 0 Likes
Who rebuilds original AC accumulator dryers for 1964 Cadillac? I have been on Classic auto air in Tampa FL wait list for over a year , There is one on Old air products web site that looks very similar to the original # 21-4214A but states it fits 1962 Gm cars, The one recommended for a 1964 Cadillac is half the length 21-4215A What is everyone using ? I would prefer to be as original as possible. Thanks
© 2024 Created by Jason Edge. Powered by