Per Tony, i am starting a new thread on my adventures with this rear main leak,
i posted a video on a 390 engine of a rear main seal replacement but the engine was out of the car,, gave some insight as to sealing and materials etc.
One of my neighbors has a hoist,(yeah!) and has allowed me to use it,, makes it a lot easier than rolling around on the asphalt in the street and is enough higher that its not too confining under there. I did have to pay attention to the lift points though as it seems you cant just put those lift arms wherever you want..
As of this evening, I have taken the exhaust loose, the steering loose, and the starter is out,, took about 4 hours to do that. I guess there is nothing earthshaking to report on any of this. Tomorrow, I will take the pan off and proceed from there.
To be clear before proceeding.
the 63 manual says to insert the bearings in there slots, do not pull off wax coating as that will aid in insertion. I do not see any wax on my gasket, so my guess they had it on the old ones.,,
Now, the question here is,, do i add a touch of oil or something to aid in that insertion process,, the manual does not suggest it, as i describe above, or, just insert dry, as is..
it does say apply rubber cement to cap and block mating surfaces, and gasket ends, but that is the only reference in the 63 manual regarding lubricaitng the seal for installation,, so is that correct?? insert dry??
the you tube video says to use lubridation after insertion so it wont be dry on start up, so i plan to do that as well.
i will try to take a few photographs of things once i get the pan off, i m sure most have seen the underside, but its my first venture in there and post them for reference.
Tags:
video https://www.youtube.com/watch?v=fgYWM39IcWs&t=9s
it should be noted that upon further research in to caddy daddy, this is a video on a 1959 biarittz 390,, not the 63 as i first thought,,,,i dont know if this matters, but that is a fact i wanted to convey
Can an impact wrench b used to REMOVE the bearing bolts
At 95 lbs torque, they r in pretty good
Never mind on the torque wrench. Cheater pipe got it..
I have a larger concern. Got the bearing out and notice it had a cut in it. Like someone out a chop saw through it. Photo attached.
Please advise
Another picture frpm inside the cap
If I remember correctly, the slot in bearing cap is normal. That is one messed up seal though. Replacing it should greatly improve your oil leak situation.
Not sure what sliced the rubber seal. When I replaced my seal several years ago, it did not have slices in it. The rubber was just hardened. I tried to find pics from then but can't. I seem to remember the slot in the bearing cap but can't say if your is normal or not. That cut does look rough in the last pic
Kurt, the slice is in the metal rib, not the seal
Oh OK. I saw some fibers in the pic & assumed that was a sliced rubber seal. If the bearing cap metal is that damaged, what does the crank look like?
Appears and feels smooth
Ok. Well at one level, thats good, at second level. Not good. May just try to find bearing, and do now while up. Are they a hard item to find?
Started by Mike Travers in 1963/64 Cadillac Specific Discussion. Last reply by Matti Roth on Tuesday. 1 Reply 0 Likes
My 61 year old radiator sprung a leak (actually a few leaks). What are you guys using as replacements? Are you replacing with copper or aluminum? How many rows are you running in the radiator? How's…Continue
Started by Jeff Donaldson in Wanted to Buy on Monday. 0 Replies 0 Likes
Hi,I need one T-3 low beam headlight if anyone has a spare they would like to sell.CheersJeffContinue
Started by Doug Scarrow in For Sale on Sunday. 0 Replies 0 Likes
just listed https://www.ebay.com/itm/266787800087Correct complete front unit coupling fits 1958 thru 1964 Cadillacs Hydramatic transmission The…Continue
Started by Doug Scarrow in For Sale on Saturday. 0 Replies 0 Likes
Just listed. https://www.ebay.com/itm/266786607755Continue
Posted by Dave Fehrle on March 23, 2024 at 3:23pm 8 Comments 0 Likes
While checking my Carter carb with engine running, I took the air cleaner off and there was a very loud hissing sound of air. I placed a piece of paper over the carb and it didn’t move up or down, is this normal?
Posted by Chase on March 21, 2024 at 5:55am 0 Comments 0 Likes
Hey everyone, has anybody done a Vintage Air AC/Heat setup in their car? I want to bypass the old vacuum setup and go with a Vintage Air Gen 2 model. Before I get started, does anyone have any experience with this? (Which model to go with, do’s and dont’s, etc.) It looks pretty involved. Any and all info/pics would be greatly appreciated. Thanks!
Posted by CHRIS CARLSON on December 6, 2023 at 10:54am 0 Comments 0 Likes
Who rebuilds original AC accumulator dryers for 1964 Cadillac? I have been on Classic auto air in Tampa FL wait list for over a year , There is one on Old air products web site that looks very similar to the original # 21-4214A but states it fits 1962 Gm cars, The one recommended for a 1964 Cadillac is half the length 21-4215A What is everyone using ? I would prefer to be as original as possible. Thanks
Posted by Les Eastling on November 15, 2023 at 10:34am 1 Comment 0 Likes
My son, unbeknownst to me, had all three of the horns on our 1963 Eldorado completely restored. We had recently added the Eldorado trumpet horn to the two standard horns and the sound was not very good... we had heard good ones so we knew something was not right... but there was not much we could do to get better sound from the 3 horns.
There is a restoration service called The Horn Works who my son…
Continue© 2024 Created by Jason Edge. Powered by