I am getting ready to order roof rail weather stripping and rear door window leading edge seals for my '63 Series 62 6 window sedan model 6229.
I've been on the websites for Rubber The Right Way, Steele Rubber Products and Metro Molded Parts. The first two listed companies have identical products, with prices on each item exactly the same as their competitor, right down to the penny. Metro's products are less in cost, but their catalog is a little confusing. They offer two different roof rail seals for this car at two different prices. The lower priced one is referred to as "super soft EPDM sponge rubber compound" and the more expensive one is listed as "black closed cell skin covered sponge." I'm curious if some of you experts know which of the two most closely duplicates the OEM product in appearance. Any general comments on your experience with any of these companies (or others) would be appreciated as well. Thank-you.
Terry Lange
Tags:
Hello Terry, it's been many years now ,but I ordered mine from Steele, and I couldn't have been happier about the look & fit .This was for my '63 6339 .HTH
I used Rubber the Right Way because they get their rubber from Steele. They do cut all flat rubber in their shop. I believe they supply Steele the flat rubber. They use to give a military discount and still might. There about 5 miles from my house and I have been by to see them. Nice guys that always try their best. Dave
Sorry Robert and Dave for me not getting back to you. I ended up splitting the order. I ordered the roof rail seals from Metro and confirmed with them over the phone that I was ordering the correct set. Unfortunately when it arrived, it looked nothing like what was displayed in their catalog either in length, design and where the curves were. I contacted them and they racked it up to mis-packaging at the factory. An exchange was made and all turned out well. I did order some more specialized parts from Rubber the Right Way, because Metro didn't make them. They were the rear quarter window lead edge seal and the lock pillar filler.
Metro's price was quite a bit less than both Rubber the Right Way and Steele Rubber, who coincidentally had identical prices right to the dollar.
Started by Jason Edge in General Discussion. Last reply by Jason Edge 4 hours ago. 4 Replies 0 Likes
So I am starting to crawl around under Dino seeing what I can fix or upgrade and as I was putting the trans linkage in a few nights ago, the rear trans mount caught my eye. I remembered that these 64…Continue
Started by Dave Fehrle in 1963/64 Cadillac Specific Discussion. Last reply by Russ Austin on Thursday. 3 Replies 0 Likes
I have finished replacing all the rear suspension and am at the last item, which is bleeding the rear brakes. I am using the Jason Edge vacuum pump method and all went well with the rear passenger…Continue
Started by Phillip Hill in 1963/64 Cadillac Specific Discussion. Last reply by Dennis P. DiBari on Wednesday. 8 Replies 0 Likes
Hi everyone im currently restoring my my front grill due to some previous clown painting it with silver frost paint and doing a dodgy job I would like to know what parts of the grill are anodised.it…Continue
Started by Mack in 1963/64 Cadillac Specific Discussion. Last reply by Dennis P. DiBari on Tuesday. 6 Replies 0 Likes
So… I do have a few of 63 Coupes, all have same setup with carbs, Pertronix, shroud, new US Radiator radiators etc … but only one of them gets a bit hot when I am hauling faster than 60mph and car…Continue
Posted by SK on June 2, 2025 at 2:20pm 2 Comments 0 Likes
Could someone post front and back photos of the 1963 right-hand kick panel with A/C?
My car didn’t come with the original kick panels, so it's a bit of a mystery to me how I should cut the backing board and carpet to fit around the A/C.
Many thanks,
-Samu
Posted by Chase on March 12, 2025 at 2:05pm 14 Comments 1 Like
Hey guys,
I have installed the same Edelbrock carb and have done everything the same as Jason’s carb and intake project. In the spring and summer months the car starts, runs and idles great! In the fall and winter months on a cold start, the car starts awful and wants to die until it warms up. I have to keep my foot on the throttle until it warms up or it will idle just terrible and try to die. Once it’s warm, it runs fantastic! Whats going on here? I was thinking of removing the…
ContinuePosted by Ray Schick on August 22, 2024 at 6:25pm 2 Comments 0 Likes
I bought this seat material thinking that it’s…
July 20, 2025 from 8pm to 9:30pm – Zoom
0 Comments 0 Likes
© 2025 Created by Jason Edge.
Powered by