63FrontLicGuard
Comment
-
Comment by Jason Edge on December 2, 2015 at 9:57pm
-
I have them but with a few dings I would let go cheap.. say $15. If you want a very nice one solid straight, ding free one I can put you on the Wait List if no one has one.
-
-
The easiest way to tell the difference is on the legs that extend down. Note that the 63 license guard on the left of picture below has a wider leg and smoother contour than the 64 license guard on the right with the thinner leg that is less smooth as it cuts rear ward more at a certain point.
In picture above: Left is 1963 and Right is 1964 front license guard.
-
-
email me at jasonedge@nc.rr.com with list of specific parts you need. I will put you on the 'wait list' for what I do not have, and give you pricing on what I do have.
Photos
Members
Forum
Front Fender Skirt Backing Bracket Access – Question + Cad Plate Love
Started by Logan Robb in 1963/64 Cadillac Specific Discussion. Last reply by Jason Edge 6 hours ago. 1 Reply 0 Likes
Hello all,I’m in the middle of swapping out the front fender skirt backing brackets on my ’64 Fleetwood and had a quick question for the group. I picked up a beautiful fresh set of cadmium plated…Continue
Power Booster Install
Started by Rob Spring in 1963/64 Cadillac Specific Discussion. Last reply by Rob Spring Apr 8. 9 Replies 0 Likes
Hey! I’ve seen the 63/64 power booster and master cylinder combination has been covered very clearly. I’m in the process of replacing mine. I was hoping someone could give me insight on a specific…Continue
1964 Cadillac Deville Neutral Safety switch and Oil Filter Housing Assembly
Started by Michael Monson in Wanted to Buy. Last reply by Russ Austin Apr 7. 3 Replies 1 Like
Hello, possibly looking a neutral safety switch for a 1964 Deville with the TH-400 and tilt steering. Also, possibly looking for an oil filter housing assembly for a 1964 429 motor. Starting to get…Continue
Complete Front End Rebuild
Started by Logan Robb in 1963/64 Cadillac Specific Discussion. Last reply by Mark Mata Apr 3. 1 Reply 0 Likes
I meant to make this a priority over the winter and didn't get that far. I've tried to source all the parts individually, but that is a daunting task. Partly because I don't want to miss any…Continue
Blog Posts
Edelbrock Carb Block off Plates
Posted by Chase on March 12, 2025 at 2:05pm 13 Comments 0 Likes
Hey guys,
I have installed the same Edelbrock carb and have done everything the same as Jason’s carb and intake project. In the spring and summer months the car starts, runs and idles great! In the fall and winter months on a cold start, the car starts awful and wants to die until it warms up. I have to keep my foot on the throttle until it warms up or it will idle just terrible and try to die. Once it’s warm, it runs fantastic! Whats going on here? I was thinking of removing the…
ContinueNew old stock seat material
Posted by Ray Schick on August 22, 2024 at 6:25pm 2 Comments 0 Likes
I bought this seat material thinking that it’s…
Loud air moving sound within carb with cleaner removed
Posted by Dave Fehrle on March 23, 2024 at 3:23pm 8 Comments 1 Like
While checking my Carter carb with engine running, I took the air cleaner off and there was a very loud hissing sound of air. I placed a piece of paper over the carb and it didn’t move up or down, is this normal?
Events
© 2025 Created by Jason Edge.
Powered by
You need to be a member of 63/64 Cadillac Website to add comments!
Join 63/64 Cadillac Website