I 3D printed a Cadillac script for my cornering light which has been also modified to work as a side marker.

Facebook Facebook

Views: 115

Comment

You need to be a member of 63/64 Cadillac Website to add comments!

Join 63/64 Cadillac Website

Comment by Dennis P. DiBari on May 21, 2025 at 6:34pm

Kurt,

     I love your cornering lights and lens script on your Caddy!!!!!!

Dennis DiBari

Comment by Bill Wolf on May 21, 2025 at 4:41pm

That looks great. I like the font.

Comment by Kurt on November 27, 2023 at 5:54pm

Thanks for the comments. It is just PLA plasic. 3D printing is a fun hobby. Would love to have a 3D printer that prints in metal but that is unlikely due to the cost. I haven't considered metal casting but might look into that. 

Comment by Roy Brosi on November 27, 2023 at 12:28pm
Looks great! Like it should have been there all along.
Comment by Jason Edge on November 23, 2023 at 8:27am

Very cool! That looks a lot like the 63 dash script.

Photos

  • Add Photos
  • View All

Forum

Power steering fluid

Started by Bobby Brown in General Discussion 5 hours ago. 0 Replies

My reservoir is a little low. Any recommendations on my purchase of refill fluid? There are likely new fluids and I’d like to buy the right product. Thanks. Continue

Dino Diaries - July 11, 2025 - Busted!

Started by Jason Edge in General Discussion. Last reply by Jason Edge yesterday. 4 Replies

So I am starting to crawl around under Dino seeing what I can fix or upgrade and as I was putting the trans linkage in a few nights ago, the rear trans mount caught my eye. I remembered that these 64…Continue

Bleeding brakes

Started by Dave Fehrle in 1963/64 Cadillac Specific Discussion. Last reply by Russ Austin on Thursday. 3 Replies

I have finished replacing all the rear suspension and am at the last item, which is bleeding the rear brakes. I am using the Jason Edge vacuum pump method and all went well with the rear passenger…Continue

Front grill

Started by Phillip Hill in 1963/64 Cadillac Specific Discussion. Last reply by Dennis P. DiBari on Wednesday. 8 Replies

Hi everyone im currently restoring my my front grill due to some previous clown painting it with silver frost paint and doing a dodgy job I would like to know what parts of the grill are anodised.it…Continue

Blog Posts

1963 RHS A/C kick panel - photos needed

Posted by SK on June 2, 2025 at 2:20pm 2 Comments

Could someone post front and back photos of the 1963 right-hand kick panel with A/C?

My car didn’t come with the original kick panels, so it's a bit of a mystery to me how I should cut the backing board and carpet to fit around the A/C.

Many thanks,

-Samu

Edelbrock Carb Block off Plates

Posted by Chase on March 12, 2025 at 2:05pm 14 Comments

Hey guys,

I have installed the same Edelbrock carb and have done everything the same as Jason’s carb and intake project. In the spring and summer months the car starts, runs and idles great! In the fall and winter months on a cold start, the car starts awful and wants to die until it warms up. I have to keep my foot on the throttle until it warms up or it will idle just terrible and try to die. Once it’s warm, it runs fantastic! Whats going on here? I was thinking of removing the…

Continue

'63 Tailfin Tales

Posted by Mark Mata on February 22, 2025 at 5:00pm 9 Comments

New old stock seat material

Posted by Ray Schick on August 22, 2024 at 6:25pm 2 Comments

I bought this seat material thinking that it’s…

Continue

Videos

  • Add Videos
  • View All

© 2025   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service