Jason, I liked the detail and information you have provided. I would like to do mine similar to yours. Can you help? Do you have trunk material? OPGI is sending the trunk product for my 63 Fleetwood. But it does cover the entire trunk as yours was done. If you do not have can you give me a reference? Thanks!! Bob

Views: 302

Facebook Facebook

Comment

You need to be a member of 63/64 Cadillac Website to add comments!

Join 63/64 Cadillac Website

Comment by Karl Schwarz on May 10, 2021 at 2:13pm

I used mostly Gorilla Glue Spray Adhesive. I also used some 3M spray adhesive (I think #77) that I had half a can of. Both worked fine and gave me time to position and reposition fabrics while also being secure once dry.

Also, I reused the backing of the piece that comes down from the back shelf, but replaced the backing on the back (taillight end) of the trunk. For the replacement backing I used Neoprene Sponge Foam Rubber that I also got on Amazon. One 15" x 60" roll of this material was just the right amount.

Comment by Karl Schwarz on May 10, 2021 at 1:29pm

I just redid my trunk. SMS Auto Fabrics sent me a sample of their fabric (about 1 1" square) and it looks essentially identical to the original fabric. I think the cost is $89/yard. It also seems to be directional (meaning it will look weird if the weave pattern is not oriented to make the weaves all go in the same direction) which will likely increase the amount of fabric needed. I don't really like the original material, and did not want to spend a lot the trunk, so I purchased my material on Amazon. I think it is similar to what OPGI sells (which is not a match to the original). The fabric I used can be found here for $60. I ordered one 4' x 20' piece that was just enough (it came as two 4' x 10' pieces). I was very happy with my choice.

You can see before, in progress, and after pictures of my trunk restoration....

Here is the end result before I put the jack and spare back in.

Comment by Jason Edge on April 9, 2021 at 2:53pm
SMS Auto Fabrics (www.smsautofabrics.com) sells the original fabric used on the trunk mat, rear walls, wheel well corners and back hump (and used on all cardboard sides for the Fleetwood and Eldorados. ) You will need about 3 yards as I recall for body styles other than the Fleetwood & Eldo.

Photos

  • Add Photos
  • View All

Forum

Bleeding brakes

Started by Dave Fehrle in 1963/64 Cadillac Specific Discussion. Last reply by Dennis P. DiBari 2 hours ago. 2 Replies

I have finished replacing all the rear suspension and am at the last item, which is bleeding the rear brakes. I am using the Jason Edge vacuum pump method and all went well with the rear passenger…Continue

Front grill

Started by Phillip Hill in 1963/64 Cadillac Specific Discussion. Last reply by Dennis P. DiBari yesterday. 8 Replies

Hi everyone im currently restoring my my front grill due to some previous clown painting it with silver frost paint and doing a dodgy job I would like to know what parts of the grill are anodised.it…Continue

Getting hot when going fast…

Started by Mack in 1963/64 Cadillac Specific Discussion. Last reply by Dennis P. DiBari yesterday. 6 Replies

So… I do have a few of 63 Coupes, all have same setup with carbs, Pertronix, shroud, new US Radiator radiators etc … but only one of them gets a bit hot when I am hauling faster than 60mph and car…Continue

Rainstorm out of nowhere!

Started by Logan Robb in 1963/64 Cadillac Specific Discussion. Last reply by Dennis P. DiBari on Monday. 1 Reply

After dinner last night, we went for a quick cruise as the weather was cooler and the sun set was looking really good!Out of nowhere, a pop up shower appeared overhead and down-poured as we were…Continue

Blog Posts

1963 RHS A/C kick panel - photos needed

Posted by SK on June 2, 2025 at 2:20pm 2 Comments

Could someone post front and back photos of the 1963 right-hand kick panel with A/C?

My car didn’t come with the original kick panels, so it's a bit of a mystery to me how I should cut the backing board and carpet to fit around the A/C.

Many thanks,

-Samu

Edelbrock Carb Block off Plates

Posted by Chase on March 12, 2025 at 2:05pm 14 Comments

Hey guys,

I have installed the same Edelbrock carb and have done everything the same as Jason’s carb and intake project. In the spring and summer months the car starts, runs and idles great! In the fall and winter months on a cold start, the car starts awful and wants to die until it warms up. I have to keep my foot on the throttle until it warms up or it will idle just terrible and try to die. Once it’s warm, it runs fantastic! Whats going on here? I was thinking of removing the…

Continue

'63 Tailfin Tales

Posted by Mark Mata on February 22, 2025 at 5:00pm 9 Comments

New old stock seat material

Posted by Ray Schick on August 22, 2024 at 6:25pm 2 Comments

I bought this seat material thinking that it’s…

Continue

Videos

  • Add Videos
  • View All

© 2025   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service