Dana G Cooper's Discussions (22)

Discussions Replied To (16) Replies Latest Activity

"Kim, I looked up the site for my starter, it is: qualitypowerauto.com  . The starter…"

Dana G Cooper replied yesterday to Back to Starter

39 1 hour ago
Reply by Jason Edge

"I had the same problem and I did the following: I Made sure the engine was tuned and…"

Dana G Cooper replied on Sunday to Back to Starter

39 1 hour ago
Reply by Jason Edge

"If they are the correct rubber "plugs" from the factory (OEM), they should have a sl…"

Dana G Cooper replied Feb 27 to water in doors 63 cdv

6 Feb 27
Reply by Kim K Kaiser

"I bought an original bias ply from Coker. Looks original and fits in the slot of my…"

Dana G Cooper replied Feb 7 to Spare tire question

2 Feb 7
Reply by Dana G Cooper

"Mine also runs about a quarter way with a 190 thermstat"

Dana G Cooper replied Nov 15, 2017 to Temperature gage

64 Nov 17, 2017
Reply by Jake Mickley

"Ok."

Dana G Cooper replied Jul 12, 2017 to Metal inline fuel filters

16 Jul 12, 2017
Reply by Tony and Ginny 429

"I agree the return line is not needed but I wanted to try to keep the original setup…"

Dana G Cooper replied Jul 12, 2017 to Metal inline fuel filters

16 Jul 12, 2017
Reply by Tony and Ginny 429

"That's interesting ! Since I have A/C here is what I did. I removed the glass filter…"

Dana G Cooper replied Jul 11, 2017 to Metal inline fuel filters

16 Jul 12, 2017
Reply by Tony and Ginny 429

"If There is not a metal filter replacement I am thinking of replacing the bowl filte…"

Dana G Cooper replied Jun 22, 2017 to Metal inline fuel filters

16 Jul 12, 2017
Reply by Tony and Ginny 429

"For What It is Worth,  I recently had an alternator go bad on my Deville so as a pre…"

Dana G Cooper replied May 7, 2017 to Replaced Voltage Regulator, now having problems.

21 May 9, 2017
Reply by Anders

RSS

Photos

  • Add Photos
  • View All

Forum

Floor Pans

Started by Tommy Nicolosi in Restoration Discussion 29 minutes ago. 0 Replies

Are the floors on 1961-1964 the same???Continue

Back to Starter

Started by Kim K Kaiser in 1963/64 Cadillac Specific Discussion. Last reply by Jason Edge 1 hour ago. 39 Replies

Ok,  short refresher,  last dec i relpaced starter w rebuilt from usa parts.  and even then,  after short runs where i got up to temp, if i shutvcar off, and then tried to start, it would drag…Continue

Current 1963/64 Cadillac Listings on eBay

Started by Jason Edge in For Sale. Last reply by Jason Edge 2 hours ago. 0 Replies

To see all 1963/64 Cadillacs Listed on eBay in the USA…Continue

Tags: ebay

'63 CDV Restomod on Iron Resurrection on Velocity Channel

Started by Ian Osborne in General Discussion 10 hours ago. 0 Replies

I just watched an episode of a show called Iron Resurrection on Velocity Channel. They did a restomod on a pretty clean survivor '63 CDV for a customer. They did an LS3 swap, air ride, complete…Continue

Blog Posts

HVAC Vacuum Valve Clip-need the one for the Power Control side

Posted by Norman Silverman on September 17, 2018 at 8:15pm 6 Comments

Hi.

Update:

I removed both 7 nipple vacuum valves and called my buddy who owns a machine shop. Tomorrow we'll re-surface the valve faces and then I'll reinstall them. HOWEVER, the one that comes out easily and comes apart with no rivet is on the Power module side. It installs on one side with a small bolt, and on the other it is held on by a clip, WHICH IS MISSING ON MY CAR. I am going to assume it is the same clip that is used on the Control Module side. Anybody got one? Happy…

Continue

7 vacuum valve-need a good one or someone to recondition mine

Posted by Norman Silverman on September 15, 2018 at 5:44pm 12 Comments

So, I've put my 7 vacuum valve from the control head side to the test, and it failed. I looked at the instructions for re-conditioning it and unless I am missing something, the instructions are missing something (about how to take off the clip that provides the tension that holds the two pieces together). 

In any case, I can't do this particular repair so I am looking for a new valve (not likely), or a good re-conditioned one, or someone who has done this before and would do mine for…

Continue

Mosiac Cadillac emblem Table

Posted by Dana G Cooper on August 30, 2018 at 10:48pm 11 Comments

Wanted to share a picture of a table my wife made for me to display with our 63 Coupe Deville. 

Inside door handle thread size

Posted by Michael Jarnagin on August 23, 2018 at 4:31pm 1 Comment

Anyone know the thread size on the inside door handle bolts mine are missing any info much appreciated 

Videos

  • Add Videos
  • View All

© 2018   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service