Jeroen Welgemoed's Discussions (38)

Discussions Replied To (28) Replies Latest Activity

"Hi.  I made a support out of a socket. Needed to grind two sides a little bit to get…"

Jeroen Welgemoed replied Oct 12, 2018 to Pistons not completely centered

18 Oct 22, 2018
Reply by Jeroen Welgemoed

"I already have a cradle made it out of a synthetic soft block. This cracked the old…"

Jeroen Welgemoed replied Oct 7, 2018 to Pistons not completely centered

18 Oct 22, 2018
Reply by Jeroen Welgemoed

"Hi Clovis. Im rebuilding my engine so the pistons and pins are new. I was planning t…"

Jeroen Welgemoed replied Oct 7, 2018 to Pistons not completely centered

18 Oct 22, 2018
Reply by Jeroen Welgemoed

"Hi Anders.  Yes they move freely. I loved to have them completely centered. But if i…"

Jeroen Welgemoed replied Oct 7, 2018 to Pistons not completely centered

18 Oct 22, 2018
Reply by Jeroen Welgemoed

"Well i went to the Samaria mountains/gorge here on Crete in Greece. As the tourists…"

Jeroen Welgemoed replied Sep 5, 2018 to Taking some time off

17 Sep 5, 2018
Reply by Jeroen Welgemoed

"Oh guys this discussion is getting real fine. just got back from the beach. And guys…"

Jeroen Welgemoed replied Sep 1, 2018 to Taking some time off

17 Sep 5, 2018
Reply by Jeroen Welgemoed

"Ghehehe. I am going to try to remember that one. We also have words for woman like t…"

Jeroen Welgemoed replied Sep 1, 2018 to Taking some time off

17 Sep 5, 2018
Reply by Jeroen Welgemoed

"The woman at the resort are not that great guys... Wont post a better picture of the…"

Jeroen Welgemoed replied Sep 1, 2018 to Taking some time off

17 Sep 5, 2018
Reply by Jeroen Welgemoed

"Greece is great russ it is my fourth time on the island of crete. Every restaurant s…"

Jeroen Welgemoed replied Aug 31, 2018 to Taking some time off

17 Sep 5, 2018
Reply by Jeroen Welgemoed

"You might be on to something with the copper gaskets. I have seen high performance c…"

Jeroen Welgemoed replied Aug 28, 2018 to Repeated leaking of exhaust manifold gaskets 1963 Cad

7 Aug 28, 2018
Reply by Tony and Ginny 429

RSS

Photos

  • Add Photos
  • View All

Forum

Current 1963/64 Cadillac Listings on eBay

Started by Jason Edge in For Sale. Last reply by Jason Edge 4 hours ago. 0 Replies

To see all 1963/64 Cadillacs Listed on eBay in the USA…Continue

Tags: ebay

Battery, alternator not charging

Started by Keith Benning in 1963/64 Cadillac Specific Discussion. Last reply by Keith Benning 13 hours ago. 10 Replies

Hello All, after replacing the voltage regulator, alternator, checking and replacing wires to alternator plug, test voltage on battery, good, voltage on alternator good.  Checked ground with multi…Continue

'64 Cadillac speedometer cable - transmission to cruise control box

Started by Don Moyer in 1963/64 Cadillac Specific Discussion. Last reply by Jason Edge 18 hours ago. 3 Replies

Hi folks - I'm new to this forum, but have owned my '64 convertible since 1993.  I recently replaced the speedo gear and seal in the transmission due to fluid leak, and noticed that the end of the…Continue

1963 transmission dipstick tube came out

Started by Karl Schwarz in 1963/64 Cadillac Specific Discussion. Last reply by Kurt yesterday. 1 Reply

I went to check the fluid in the transmission on my 1963 Series 62 convertible and when I pulled on the dipstick ring the whole tube came out. I got it back in the hole, sort of, but it is loose.…Continue

Blog Posts

Frame Markings

Posted by Gene McIlroy on August 12, 2019 at 6:26pm 1 Comment

Just got my frame back from powder coating so thought I would post photos of the front and rear frame markings.…

Continue

Lining up the drive shaft

Posted by Dominic Salemi on August 12, 2019 at 5:47pm 2 Comments

Can anyone shed some light on how to position the complete drive shaft in the correct position? I want to make sure my drive shaft is installed properly.

Thanks

Dominic

Upper A Arm Rubber Bumpers

Posted by Gene McIlroy on August 12, 2019 at 1:30pm 3 Comments

I have found a very good replacement part for the Upper A Arm Bumpers.  The top part is identical to the originals the bottom can be used as is or after a few minutes with a belt sander can be ground to the V shape as the originals were.  The replacement bumpers are for a 2001 to 2005 S10 Sanoma or Blazer.  Part number is on the box in the photos.  First photo is the box next to the box is the S10 part and an original.  Next photo shows my sanded down part next to an original.…

Continue

Roof motor

Posted by Dermot Robinson on August 11, 2019 at 8:44am 2 Comments

Replacing my convertible roof motor.

Has anyone any experience or advice on replacing the roof motor on a 1964 Cadillac Deville .

Please..

Events

Videos

  • Add Videos
  • View All

© 2019   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service