Gene McIlroy's Discussions (55)

Discussions Replied To (53) Replies Latest Activity

"Hose mounts on end of evaporator case and just drains on the ground."

Gene McIlroy replied Mar 1, 2019 to AC drain hose and electrical question 63 Deville

31 Mar 1, 2019
Reply by Clovis

"Chris Source for the drain tube: Old Air Products 1201 Forum Way Fort Worth, TX 7814…"

Gene McIlroy replied Feb 27, 2019 to AC drain hose and electrical question 63 Deville

31 Mar 1, 2019
Reply by Clovis

"Wow, that's a bunch,  Do you remember what the part and part number was that you fou…"

Gene McIlroy replied Jan 8, 2019 to New drivers side door jamb rubber wire boot

9 Jan 26, 2019
Reply by Russ Austin

"Russ Have you checked on just having the "tit" rivets made for the boots.  I have or…"

Gene McIlroy replied Jan 8, 2019 to New drivers side door jamb rubber wire boot

9 Jan 26, 2019
Reply by Russ Austin

"John At the top of the home page see a group of headings.  Click on the Help button.…"

Gene McIlroy replied Dec 12, 2018 to 1964 seat belt length

4 Dec 13, 2018
Reply by Mark S Anderson

"Good Luck with your surgery and have a Happy Thanksgiving Gene McIlroy"

Gene McIlroy replied Nov 22, 2018 to Hey Jason,

50 Nov 28, 2018
Reply by Tony and Ginny 429

"Tim I have not looked up the numbers but the basic difference between a 63 and 64 wi…"

Gene McIlroy replied Aug 22, 2018 to Wiper motors

2 Aug 22, 2018
Reply by Jason Edge

"They show up on Ebay every once in a while. Check it often!"

Gene McIlroy replied Jul 21, 2018 to Rear center speaker 63 Caddy Convertible

2 Jul 28, 2018
Reply by Jon Ettman

"Check your fuel sediment bowl for possible water in the gas. Lots of rain in your ar…"

Gene McIlroy replied Mar 3, 2018 to stranded,,!!!

82 Mar 19, 2018
Reply by Tony and Ginny 429

"Tom There is a post on this site by Maurice Lapoiinte, It was titled "My interior re…"

Gene McIlroy replied Jan 5, 2018 to "64 convertible Fronr seat rebuild

20 Jan 7, 2018
Reply by tom servas

RSS

Photos

  • Add Photos
  • View All

Forum

Bendix Power Brake Unit Power Section

Started by Mathis Richter in 1963/64 Cadillac Specific Discussion. Last reply by Chris Codd yesterday. 7 Replies

Hi,I have a huge problem my POWER SECTION of the ``Master-VAC Power Brake unit 9´´Diameter ´´ from Bendix is Broken and I can't open it to replace al the rubber parts did some of you have auch Power…Continue

Third brake light -help please.

Started by paul k in 1963/64 Cadillac Specific Discussion. Last reply by Jason Edge yesterday. 8 Replies

Did anybody from the club install third brake light in the rear window in his Cadillac? I have problem to figure out how to do it. Can I just run wire from break pedal switch and second wire connect…Continue

Extra speakers in the cadillac.

Started by paul k in 1963/64 Cadillac Specific Discussion yesterday. 0 Replies

Ok, I have another question. Since I will run wire for a brake light I might run speakers wires.I would like to install 2 extra speakers or maybe 4. What is best option. I do have 2 speakers already-…Continue

429 and 400 trans. for sale

Started by Mark C Bills in For Sale. Last reply by Tony and Ginny 429 on Monday. 6 Replies

I have an excellent running 429 with 400 trans.recently removed from my 64. It has electronic ignition, new water pump,new fan and clutch(not pictured),new fuel pump,Holley 650 vac. sec. carb. with…Continue

Blog Posts

1964 Cadillac Fleetwood sixty special / transmission dipstick needed

Posted by Pablo on September 20, 2020 at 9:57pm 1 Comment

How are you doing folks, I’m looking for a transmission dipstick, any info I will appreciated, thank you very much

1963 Cadillac hood driver side hinge

Posted by Steven on September 16, 2020 at 9:23am 1 Comment

Hello,

 Does anyone know were I can buy a 1963 Cadillac hood driver side hinge or is there any other hinge that would fit? 

Thanks

Steven

Bad Guage?

Posted by Karl Schwarz on August 26, 2020 at 3:08pm 6 Comments

So I am troubleshooting my fuel gauge issue. I bought a new sender and tested it. It  it goes from 1-ohm (empty) to 35-ohm (full). When I test it (outside the tank), when the float is in the up (full) position it only moves the gauge to about 1/2 full. When at the bottom (empty) position the gauge shows empty. This is the same issue I have when I fill and then use the gas in the tank - the gauge never reads ore than half full. Based on what I've read on this thread it would seem like the…

Continue

Website

Posted by Fritz Seitz on August 11, 2020 at 2:35am 0 Comments

I have been working on a website-----www.fritzsautorepair.com-----

Does anyone have suggestions?

Videos

  • Add Videos
  • View All

© 2020   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service