I recently purchased a 1963 Coupe deVille. The transmission will only shift 1st to 3rd. I put the car on a lift and drained the pan and torus. I removed the shift valve body and coupling valve body, cleaned the pistons and bores, replaced the filter and fluid and adjusted the TV rod per spec. No change in the way it shifts. I have read that the aluminum cover on the fluid coupling is prone to cracking which will also cause the trouble I am having. I feel a rebuild is is in my future. Other than Gene's transmission in California, can anyone recommend a shop on the east coast? I live in Virginia Beach, VA. John.
Tags:
Hey John , go to the Cadillac / Lasalle Club site and post your question . Im sure somebody can help you find a Trans guy by your area, Good Luck. Ray
John, did you happen to find any other shops or what was wrong? My transmission is doing the same.
I called Gene and talked to him for an hour. He is near genius but just a little more than I wanted to pay.
Josh, I live in Virginia Beach Virginia and finally found a shop in my area to overhaul my transmission The shop is CarLife Transmissions in Norfolk Virginia. The owners name is Fred Kent and he is very knowledgeable. Before I could tell him what steps I had taken to correct the problem he told me exactly what was wrong. I had already researched the problem and knew that the secondary fluid coupling was leaking. The only way to correct it is to pull the tranny. I dropped off my car at the shop 2 weeks ago and and am expecting it back any day now. He quoted me $3980 (must be the going rate for a Jetaway) for the overhaul and had every part needed for the rebuild. That price included removal and installation. Yes, I know it is quite a bit but at least I know it will be done right.
Started by Jason Edge in General Discussion. Last reply by Bill Wolf on Friday. 36 Replies 0 Likes
I had brought up the topic of radiator leaks as a discussion topic for our Chapter Zoom meet-up this past Sunday and thought I would share on our website for everyone and probably do a more formal…Continue
Started by Frank Murch in 1963/64 Cadillac Specific Discussion. Last reply by Bill Wolf on Friday. 2 Replies 0 Likes
Original seats had a crest on the center arm rest. Does anybody know where I could embose a crest in new material for a reupolstry?Continue
Started by Norman Silverman in General Discussion. Last reply by Norman Silverman on Thursday. 11 Replies 0 Likes
Hello AllI have taken off my dash top and started replacing dash bulbs with LED's for greater visibility. Some questions:1) To replace the Gauge bulb it looks like easier access is had by removing…Continue
Started by Richard Stanley in 1963/64 Cadillac Specific Discussion. Last reply by Bill Wolf on Wednesday. 3 Replies 0 Likes
I just replaced my tires from Diamondback (I had bad results in the past from Coker). It was the second time, due to the age of the tires. About 18 years ago Diamondback made custom whitewalls…Continue
Posted by SK on June 2, 2025 at 2:20pm 2 Comments 0 Likes
Could someone post front and back photos of the 1963 right-hand kick panel with A/C?
My car didn’t come with the original kick panels, so it's a bit of a mystery to me how I should cut the backing board and carpet to fit around the A/C.
Many thanks,
-Samu
Posted by Chase on March 12, 2025 at 2:05pm 14 Comments 1 Like
Hey guys,
I have installed the same Edelbrock carb and have done everything the same as Jason’s carb and intake project. In the spring and summer months the car starts, runs and idles great! In the fall and winter months on a cold start, the car starts awful and wants to die until it warms up. I have to keep my foot on the throttle until it warms up or it will idle just terrible and try to die. Once it’s warm, it runs fantastic! Whats going on here? I was thinking of removing the…
ContinuePosted by Ray Schick on August 22, 2024 at 6:25pm 2 Comments 0 Likes
I bought this seat material thinking that it’s…
© 2025 Created by Jason Edge.
Powered by