body side molding clips
Trying to figure out how to install body side moldings. I have my shop manual out, I've searched Caddy Daaddy and am still at a loss as to what clips and other hardware I need to get this job done.Is there any body willing to walk me thru this mess?
1964, 62 series, 6239, 4 window
Thanks,
Wayne Morris
Replies to This Discussion
-
Permalink Reply by Russ Austin on
-
What clips do you have?
-
Permalink Reply by Wayne Morris on
-
I don't have any clips at this time
-
Permalink Reply by Jason Edge on
-
I have the fender, door, and rear qtr side trim fasteners and have been selling them for I guess a decade now. I can send pictures and explain how they go on, but I am heading out a for a 5 day road trip to pick up the next parts car. If you can wait until After Feb 8, email me at jasonedge64@outlook.com and I will send pictures, pricing, and how they attached. Jason.
-
-
You can see rear qtr fasteners now by Clicking Here.
-
-
Thank you Jason
Members
Forum
where to find 1963 Cadillac Plastic Door Pin Anchors
Started by Frank Murch in 1963/64 Cadillac Specific Discussion 16 hours ago. 0 Replies 0 Likes
Hi allwhere can I find these - 1963 Cadillac Plastic Door Pin Anchors. Mine are from1963 and a little tiredThanksContinue
Rear Main Seal Oil Leak Fix with Bearing Cap Modification
Started by Kurt in 1963/64 Cadillac Specific Discussion. Last reply by Matti Roth 19 hours ago. 15 Replies 4 Likes
Many owners have reported oil leaks at the rear main seal even after replacing the seal, myself included. Recently Tony Lentini found a Serviceman bulletin published in February 1965 which details a…Continue
Future of CLC Judging
Started by Jason Edge in Restoration Discussion. Last reply by Jason Edge on Thursday. 6 Replies 0 Likes
First, A Big Thank You to CLC Chief Judge Bill Anderson for taking on this daunting task of overhauling the CLC judging system. The old system was very good, however, I believe what Bill and the…Continue
front seat crest
Started by Frank Murch in 1963/64 Cadillac Specific Discussion. Last reply by Frank Murch on Tuesday. 3 Replies 0 Likes
Original seats had a crest on the center arm rest. Does anybody know where I could embose a crest in new material for a reupolstry?Continue
Blog Posts
1963 RHS A/C kick panel - photos needed
Posted by SK on June 2, 2025 at 2:20pm 2 Comments 0 Likes
Could someone post front and back photos of the 1963 right-hand kick panel with A/C?
My car didn’t come with the original kick panels, so it's a bit of a mystery to me how I should cut the backing board and carpet to fit around the A/C.
Many thanks,
-Samu
Edelbrock Carb Block off Plates
Posted by Chase on March 12, 2025 at 2:05pm 14 Comments 1 Like
Hey guys,
I have installed the same Edelbrock carb and have done everything the same as Jason’s carb and intake project. In the spring and summer months the car starts, runs and idles great! In the fall and winter months on a cold start, the car starts awful and wants to die until it warms up. I have to keep my foot on the throttle until it warms up or it will idle just terrible and try to die. Once it’s warm, it runs fantastic! Whats going on here? I was thinking of removing the…
ContinueNew old stock seat material
Posted by Ray Schick on August 22, 2024 at 6:25pm 2 Comments 0 Likes
I bought this seat material thinking that it’s…
Events
Videos
© 2025 Created by Jason Edge.
Powered by
