Hello all, I was wondering if anyone has done an efi conversion on their vehicle. I had the Holley Sniper installed and am very happy with the system except for the very annoying noise coming from the in line fuel pump. I am looking to go to an in tank pump but the retro fit pumps from Holley are for tanks that are at least 7 inches deep. Just wondering if anyone has dealt with this same issue. I do apologize if I have posted this in the wrong area as I am not super familiar with the site. Thanks for any input or advise

Facebook Facebook

Views: 666

Reply to This

Replies to This Discussion

Hi Charles,

I have the Holley Sniper in my car and I'm using an in-tank pump.  I used the Holley in-tank module part number 12-130, but that is for tanks 7" deep at a minimum, so I had to modify the way it drops in.  I also bought a new tank (The same one they sell at OPGI) and it has a recess stamped in it that creates room for modern drop in EFI pumps.  The orginal tank doesn't have this recess.  Anyway, I had to modify the pump and the mod isn't for the faint of heart because the pump is expensive.  You basically have to modify the bracket and the tubing so that it drops in on an angle instead of straight down.  The pickup Holley uses is called "hydramat".  Holley makes different shapes than the straight piece provided.  I can't recall which one I used on mine.  I've had mine running since 2018 and never had an issue - the sniper is the best mod I ever made and you really can't tell it's there under the factory air cleaner (which I modified to fit the larger sniper inlet).

Hope that helps!

Just found this article.  Wish this was available in 2018 when I did mine...How To Install A Sniper EFI Fuel Pump Module Kit Into A Shallow Fue...

RSS

Photos

  • Add Photos
  • View All

Forum

Getting hot when going fast…

Started by Mack in 1963/64 Cadillac Specific Discussion. Last reply by Dennis P. DiBari 9 hours ago. 6 Replies

So… I do have a few of 63 Coupes, all have same setup with carbs, Pertronix, shroud, new US Radiator radiators etc … but only one of them gets a bit hot when I am hauling faster than 60mph and car…Continue

Rainstorm out of nowhere!

Started by Logan Robb in 1963/64 Cadillac Specific Discussion. Last reply by Dennis P. DiBari yesterday. 1 Reply

After dinner last night, we went for a quick cruise as the weather was cooler and the sun set was looking really good!Out of nowhere, a pop up shower appeared overhead and down-poured as we were…Continue

Convertible bumper jack

Started by Alan Clark in 1963/64 Cadillac Specific Discussion. Last reply by Logan Robb yesterday. 11 Replies

My car lacks the mechanism or spring needed to hold the jack in the storage slot on the right side of the trunk.  Anyone have a picture of the item I should find?Continue

Front grill

Started by Phillip Hill in 1963/64 Cadillac Specific Discussion. Last reply by Dennis P. DiBari yesterday. 6 Replies

Hi everyone im currently restoring my my front grill due to some previous clown painting it with silver frost paint and doing a dodgy job I would like to know what parts of the grill are anodised.it…Continue

Blog Posts

1963 RHS A/C kick panel - photos needed

Posted by SK on June 2, 2025 at 2:20pm 2 Comments

Could someone post front and back photos of the 1963 right-hand kick panel with A/C?

My car didn’t come with the original kick panels, so it's a bit of a mystery to me how I should cut the backing board and carpet to fit around the A/C.

Many thanks,

-Samu

Edelbrock Carb Block off Plates

Posted by Chase on March 12, 2025 at 2:05pm 14 Comments

Hey guys,

I have installed the same Edelbrock carb and have done everything the same as Jason’s carb and intake project. In the spring and summer months the car starts, runs and idles great! In the fall and winter months on a cold start, the car starts awful and wants to die until it warms up. I have to keep my foot on the throttle until it warms up or it will idle just terrible and try to die. Once it’s warm, it runs fantastic! Whats going on here? I was thinking of removing the…

Continue

'63 Tailfin Tales

Posted by Mark Mata on February 22, 2025 at 5:00pm 9 Comments

New old stock seat material

Posted by Ray Schick on August 22, 2024 at 6:25pm 2 Comments

I bought this seat material thinking that it’s…

Continue

Videos

  • Add Videos
  • View All

© 2025   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service