I have noticed that after I drive for 5-10 miles or more and then shut off the car, it hesitates when I go to start? Anyone experience this before and if so, what was the fix?
Tags:
Alternators will only produce what is required, and as I recall most alternators actually only produce up to about 2/3's the rated amperage under normal rpm/driving anyway. So with that 55 amp factory alternator it might be producing say up to 30 amps max at any moment under extreme max current draw load. This is why the factor 10 gauge alternator to battery (secondary charging) wire is sufficient ... but one reason why I wanted to move away from the considerably smaller 14 gauge Heartbeat City sources wires reproduced for the 1969 Camaro, and get M&H to produce wires with the correct factory 10 gauge. (I guess even back then, the Cadillacs were pulling much more power than the average Camaro or Mustang).
So, with that 100 amp alternator, unless you are installing a Giga-Splat-Velocity-Blaster in the trunk that draws 50+ amps you are probably never going to draw (ie. the alternator produce) anywhere near 100 amps. If you have the mega-amp-mega-power-draw sound system (that rivals the soundstage at an AC/DC concert), then you might want to get M&H to fabricate a cable with a thicker alternator wire (8 ga, 6 ga, 4 ga, etc).
Great work Dave. It's great when GEN light goes out and it's not overcharging. I remember going through that last year.
Dennis DiBari
Dave, That is great news. If your car is wired correctly, removing the battery cable while running is a quick & easy way to find out if the alternator is working. I actually just ordered a couple of rebuilt alternators through AutoZone today as I had a $45 reward to use, and like to keep a couple of them ready to go on the shelf.
Started by Jason Edge in General Discussion. Last reply by Bill Wolf yesterday. 36 Replies 0 Likes
I had brought up the topic of radiator leaks as a discussion topic for our Chapter Zoom meet-up this past Sunday and thought I would share on our website for everyone and probably do a more formal…Continue
Started by Frank Murch in 1963/64 Cadillac Specific Discussion. Last reply by Bill Wolf on Friday. 2 Replies 0 Likes
Original seats had a crest on the center arm rest. Does anybody know where I could embose a crest in new material for a reupolstry?Continue
Started by Norman Silverman in General Discussion. Last reply by Norman Silverman on Thursday. 11 Replies 0 Likes
Hello AllI have taken off my dash top and started replacing dash bulbs with LED's for greater visibility. Some questions:1) To replace the Gauge bulb it looks like easier access is had by removing…Continue
Started by Richard Stanley in 1963/64 Cadillac Specific Discussion. Last reply by Bill Wolf on Wednesday. 3 Replies 0 Likes
I just replaced my tires from Diamondback (I had bad results in the past from Coker). It was the second time, due to the age of the tires. About 18 years ago Diamondback made custom whitewalls…Continue
Posted by SK on June 2, 2025 at 2:20pm 2 Comments 0 Likes
Could someone post front and back photos of the 1963 right-hand kick panel with A/C?
My car didn’t come with the original kick panels, so it's a bit of a mystery to me how I should cut the backing board and carpet to fit around the A/C.
Many thanks,
-Samu
Posted by Chase on March 12, 2025 at 2:05pm 14 Comments 1 Like
Hey guys,
I have installed the same Edelbrock carb and have done everything the same as Jason’s carb and intake project. In the spring and summer months the car starts, runs and idles great! In the fall and winter months on a cold start, the car starts awful and wants to die until it warms up. I have to keep my foot on the throttle until it warms up or it will idle just terrible and try to die. Once it’s warm, it runs fantastic! Whats going on here? I was thinking of removing the…
ContinuePosted by Ray Schick on August 22, 2024 at 6:25pm 2 Comments 0 Likes
I bought this seat material thinking that it’s…
© 2025 Created by Jason Edge.
Powered by