My AC compressor is leaking from the groove I marked with the little screwdriver. It is a broken shaft seal, correct? Where can I get a new seal and do I really need the seal remover tool J-9392 for removal and installation? I already searched at Rockauto without luck.

Facebook Facebook

Views: 707

Reply to This

Replies to This Discussion

I'm keen to know this one as well. Mine has started to weep there.

Unfortunately this is a weakness of the A6 compressor. Every car I have owned with the A6 compressor has leaked from the shaft seal. I have never tried replacing the shaft seal but rather, replacing the compressor. The replacement A6 compressors will go for a year or 2 and then leak from the shaft seal. I never had an A6 fail on me but I hated the oily mess under the hood. It was difficult to keep the engine bay clean. There is a drop-in replacement for the A6 that is half the weight and half the drag and does not have the bad shaft seal design. It uses the same mounting, belt, & hoses. I think there are a few different brands. Here is the one I chose. https://www.apairinc.com/shopping/productDetails.aspx?i=134166. I liked it because it is black & has a larger pulley with a dust cover. To my surprise, when I received it.it was natural aluminum, not black.I called and asked about that and was told that the black ones are no longer available. I painted it myself and it turned out good. It works very well and I'm happy to no longer have oil slung all over the engine bay. You can try changing out your shaft seal but I believe it will just leak again in a short while from my personal experience. I live in central Texas where it gets very hot in the Summer so for me this upgrade was more important than originality. Here are pictures from my upgrade:

I think i heard, some gases will eat the seals over time.

I might have to upgrade to a newer style compressor.

Hi Mark,

they are all filled with R134a but with mineral oil? Or do they still run all with R12? R12 is absolutely impossible to get or refilled here in Germany. 

Lucky boy :)

We haven't R12 in Australia for ages now.

Three years ago I gassed up on R437A, that's now gone and R413A is the next one and its hard to get now. I think i'm going to end up with R134A when I change the compressor later in the year. But, I have got 6 degrees Celsius at the vents at the moment.

Never heard of it!

I did a lot of research when I decided to upgrade my compressor. I have had other cars with A6 compressors in the past that leaked oil from the shaft seal running R12 and mineral oil. My research showed it was a common problem and there is supposedly an upgraded shaft seal that helps http://www.v8buick.com/index.php?threads/a6-compressor-shaft-seal-r.... The seal is available if you want to try it. https://www.ebay.com/itm/AC-GM-Compressor-Lip-Shaft-Seal-R4-V5-HD6-...

I just decided that I wanted the benefits of a modern compressor (less weight, less drag, designed for R134a, etc) and it is a drop in replacement for the A6.

The part Tony mentioned is called an STV eliminator kit which converts to system to a clutch cycling system https://www.oldairproducts.com/product/50-2503-stv-eliminator-kit.

I did not install the STV eliminator kit on my car. I was getting very good performance after converting the system to R134a with the A6 compressor but got tired of the oily mess from the shaft seal.

Now with the new compressor (10PA20HD) I'm getting  great performance and no oily mess. One other addition I made for the upgrade is to install a pusher fan in front of the condenser. This helps lower the pressure on the high side. Another option is to install a high density condenser.

To Mark's point, the system was designed for R12. Life is simpler if you have access to R12. If you don't, the system can be converted if you take the proper steps.

TA-Motor is recommending a recharge-kit from Duracool. I was planning to buy a kit and a new drier/accumulator and try it on my car. But now when reading about the leaking compressor I think that would be a waste of money. Guess the best plan of action is to replace the compressor and drier and then have the system vacuum tested before refilling with whatever is available.

Another supplier for parts in Europe is Hansen Racing. Seems a bit cheaper when comparing to TA.

In additon to my steeering project,, i have been wanting to change the complressor on my 63 as well,, i read aobut those lighter replacemnt compressors.   Mine is the original and at a minimum,  the bearing is locked up,,, i had same problem on 73 and replaced the bearing,,, but this thing is 10 years older,, and i want less stress on the engine.  i do miss ac too,, i can t hear my music with  all the windows down,,,

SO,,, do you have to take the car to an ac person to unhook all those hoses..and do you have to ge t anothe kit of some sort to hook up the new hoses that have the new refriderant..i have read they have gases and pressure,,,so what is the best way to go bout that

I took my hoses to a business that rebuilds hoses.They take the fittings and splice them to new barrier rubber hose. I used my original hoses for years with the A6 compressor running R134a with no issues. I just decided to replace the 56 year old rubber hoses when I installed the new compressor. The compressor is a drop-in replacement so it works with the stock mounting & hoses. I did need a metric cap screw to attach the hose manifold to the compressor.

When the shop filled the system with R134a it was seal.
I drove to a meeting with some friends to Austria with the AC on all the time at very warm weather and had a leak at the new shaft seal again. But probably the shop filled too much R134a. As I know now, the system should be filled not more than 3.35 pounds.
I found a good chart here: https://ricksfreeautorepairadvice.com/convert-auto-r12-system-to-r1...

So, probably the pressure is too high. I hadn't time to check it again, but I'm planning it in the next weeks.

I'll keep you updated

RSS

Photos

  • Add Photos
  • View All

Forum

Clock Removal

Started by Jeff Donaldson in General Discussion. Last reply by Jason Edge 21 hours ago. 2 Replies

Hello Everyone,I tried to remove my clock today and couldn't seem to get it to rotate more than a 16th to an 8th of an inch. I followed the instuctions in the manual (counterclockwise approximately…Continue

Dino Diaries - All Jacked Up For Christmas!

Started by Jason Edge in General Discussion yesterday. 0 Replies

I have very limited space in my 3 bay garage with the left and right bay used for storage and work tables, etc leaving the narrow center aisle for my 1964 Coupe de Ville Dino. Six years ago I bought…Continue

Power Brake Booster

Started by Stephen Pechenik in General Discussion. Last reply by Bill Wolf yesterday. 13 Replies

Hello Co-Members,I recently purchased a  low mileage1963 Sedan Deville Park Avenue.  It is extremely solid and runs well.  Neverthelss, it has minor problems that need to be addressed before I can…Continue

Body side molding install help needed

Started by Wayne Morris in 1963/64 Cadillac Specific Discussion. Last reply by Wayne Morris on Saturday. 6 Replies

I am in the process of trying to install body side molding. I have completed installing the two front fender pieces and now trying ti figure out the rest.…Continue

Blog Posts

New old stock seat material

Posted by Ray Schick on August 22, 2024 at 6:25pm 2 Comments

I bought this seat material thinking that it’s…

Continue

Loud air moving sound within carb with cleaner removed

Posted by Dave Fehrle on March 23, 2024 at 3:23pm 8 Comments

While checking my Carter carb with engine running, I took the air cleaner off and there was a very loud hissing sound of air. I placed a piece of paper over the carb and it didn’t move up or down, is this normal?

Vintage Air AC

Posted by Chase on March 21, 2024 at 5:55am 0 Comments

Hey everyone, has anybody done a Vintage Air AC/Heat setup in their car? I want to bypass the old vacuum setup and go with a Vintage Air Gen 2 model. Before I get started, does anyone have any experience with this? (Which model to go with, do’s and dont’s, etc.) It looks pretty involved. Any and all info/pics would be greatly appreciated. Thanks!

accumulator dryer

Posted by CHRIS CARLSON on December 6, 2023 at 10:54am 0 Comments

Who rebuilds original AC  accumulator dryers for 1964 Cadillac? I have been on Classic auto air in Tampa FL wait list for over a year ,  There is one on Old air products web site that looks very similar to the original # 21-4214A but states it fits 1962 Gm cars, The one recommended for a 1964 Cadillac is half the length 21-4215A    What  is everyone using ? I would prefer to be as original as possible. Thanks

Videos

  • Add Videos
  • View All

© 2024   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service