Im into removing door panel for water barrier and tge dand maual vent handle will not budge. I dnt see any screw holding it on the threaded stem, and other than forcibly prying off, which hasnt fared well either, i dnt know what to do and dnt wat to break the plastick handle, nor did i see any direct book instructions. Am i missing something?
Tags:
Check the shop manual, it should state how to remove the handle
I call myself reading it. In the body section under doors, guess i missed it. I hv since found an old article on the site about a spatula tool. Found one at store, will try it
Harbor Freight $6.99 for the set, use tool on right for vent handle.
i found one at oreilly,
i found a you tube video, guy used this tool on 60s GM windows,, he slid it over the handle, and it worked in about 1 second,, mine,, however did not, i saw the clip he was pushing down in his video, but apparently, the clip in mine had gotten stuck or somehow turned, long story short, after wedging pushing twisting prying for 4 hours, it came off..i could see where the clip had gotten stuck, i was almost at he point of cutting off as it simply would not move and pushing and pulling that clip was not working, finally, caught it with vise grips needle nose and pulled it out.. hand came off,, real pain in the azz.. ,, got the paper off, wire brushed the bottom of the inside of door, vacuumed it out, and paint with a good coat of rust in hibitor on the inside bottom.. just surfrace rust mostly,, but, got it out and re sprayed,
not in any hurry to do other side after all that,,
Old cars are definitely a labor of love. I find that beer and classic rock helps keep the calm in my garage.
The good news is that re-installing them is easy. Just put the clip back on the handle into the groove it came out of, and push the handle back onto the shaft until the clip clicks back into place. Good luck on the other side!
Started by Doug Scarrow in Wanted to Buy. Last reply by Dennis P. DiBari yesterday. 1 Reply 0 Likes
for close to 20 years I have had a lovely Club Decal on my windshield now I wish to replace the windshield and would love to buy a decal if any one has one available See attached photosContinue
Started by Jordan Johansen-Moe in 1963/64 Cadillac Specific Discussion. Last reply by Jordan Johansen-Moe on Tuesday. 2 Replies 0 Likes
Is anyone here planning on going to the Back to the 50’s car show in Minnesota?
Started by Frank Murch in 1963/64 Cadillac Specific Discussion. Last reply by Jason Edge on Sunday. 2 Replies 0 Likes
Hi allwhere can I find these - 1963 Cadillac Plastic Door Pin Anchors. Mine are from1963 and a little tiredThanksContinue
Started by Kurt in 1963/64 Cadillac Specific Discussion. Last reply by Matti Roth Jun 14. 15 Replies 4 Likes
Many owners have reported oil leaks at the rear main seal even after replacing the seal, myself included. Recently Tony Lentini found a Serviceman bulletin published in February 1965 which details a…Continue
Posted by SK on June 2, 2025 at 2:20pm 2 Comments 0 Likes
Could someone post front and back photos of the 1963 right-hand kick panel with A/C?
My car didn’t come with the original kick panels, so it's a bit of a mystery to me how I should cut the backing board and carpet to fit around the A/C.
Many thanks,
-Samu
Posted by Chase on March 12, 2025 at 2:05pm 14 Comments 1 Like
Hey guys,
I have installed the same Edelbrock carb and have done everything the same as Jason’s carb and intake project. In the spring and summer months the car starts, runs and idles great! In the fall and winter months on a cold start, the car starts awful and wants to die until it warms up. I have to keep my foot on the throttle until it warms up or it will idle just terrible and try to die. Once it’s warm, it runs fantastic! Whats going on here? I was thinking of removing the…
ContinuePosted by Ray Schick on August 22, 2024 at 6:25pm 2 Comments 0 Likes
I bought this seat material thinking that it’s…
June 22, 2025 from 8pm to 9:30pm – Zoom
0 Comments 1 Like
© 2025 Created by Jason Edge.
Powered by