Last fall I replaced my rear yoke and trailing arm bushings . Now with 410 miles on them the large

  rear trailing arm bushings are done . I contacted Rare Parts the maker and they were defensive and

  wanted me to purchase new ones and if sent the old ones back they,  upon inspection would  reimburse the original seller  (Old Parts) a seller on ebay. Seemed like a lot of hoops to jump through so I inquired at all the

known Cadillac Suppliers and it seems the Rare Parts is the only maker of the RP15606 bushings . Further

 internet searches found this is a common problem. This has led to Dan McNarry and Russ Austin heading up making replacement arms with high tech bushings that do not distort and last. Rare Parts needs to retool and use rubber that will last .  In the mean time DO NOT  purchase trailing arm bushings from them with the

expectation they will last as I assure you they will fail quickly

Views: 1637

Attachments:

Reply to This

Replies to This Discussion

Correction 

Make that —- the BOMB !!!

Hello, Dan McNarry here. I haven't logged in to this site in quite some time. The subject of the poor quality trailing arm bushings seems to have generated quite a lot of "buzz". Just to re-iterate some of what has been discussed, the replacement bushings that I installed were worse than the worn out factory ones they replaced. The originals wore out in a vertical manner as in the round hole in the bushing became an elongated oval oriented vertically. The rubber was still hard however and the axle didn't move as much forward or backward as the replacement ones. The aftermarket replacement ones are terrible. They sag vertically very soon after installation and as the video shows, have lots of fore aft movement. If you watch the video to the end, notice that when I turn into the alley behind my garage (pavement to gravel) the axle does a wild kind of yaw where one side goes forward while the other side goes back. Crazy. They were two years old at that time. 

I saw where one member was complaining about the appearance of the replacement arms that I build. I make no apologies for that as they are designed to be robust and affordable. I sell these in limited numbers and the machine shop costs are high. I only make the bushing sleeves and the spring locator myself, all the other parts are made for me. The reason that I use a machine shop is that they can CNC cut the bushing sleeve holes in the trailing arm tubes very accurately ensuring that all trailing arms have the same length preventing a customers car from dog tracking. When I made the prototype set, even though I carefully laid out the holes, drilled pilot holes and used a slow speed hole saw in my drill press, the two trailing arms came out at different lengths center to center. I had to correct that with a solid hour of hand filing. 

The rest of the parts are water jetted which is particularly helpful in making the parking brake cable tab bracket. They are designed as a solution to a problem that is durable and use inexpensive and easy to replace polyurethane bushing. The bushings can be replaced by the average home mechanic without the use of a press. This is not a big money making enterprise but a service to fellow Cadillac enthusiasts. I don't advertise the fact but I pay the brokerage fee on shipping, the customer just pays the actual shipping charge. As most of my customers are in the US, you don't get penalized by my shipping them from Canada. This is the same for my European customers. The steel used is sourced by the machine shop from the USA as customers will notice by the stamps on the trailing arm tubes. 

I would like to thank those of you who are customers and I would like to thank Russ for being an advocate of these replacement trailing arms. He has been more than patient in his responses to questions and I am very grateful for his support. 

Sincerely,

Dan

RSS

Photos

  • Add Photos
  • View All

Forum

Rear shelf deck

Started by mark zimmerman in 1963/64 Cadillac Specific Discussion 1 hour ago. 0 Replies

Hi does anyone know what yo have to do to remove the rear deck board that covers the speaker and defroster? is it screwed down ?glued?ThanksContinue

Current 1963/64 Cadillac Listings on eBay

Started by Jason Edge in For Sale. Last reply by Jason Edge yesterday. 0 Replies

To see all 1963/64 Cadillacs Listed on eBay in the USA…Continue

Tags: ebay

I Whipped Out My Horn and Waxed It Today!

Started by Jason Edge in General Discussion. Last reply by john w. warner on Friday. 6 Replies

This got some humorous replies on Facebook and wanted to share here on the 63/64 site.I was installing the lower hood latch with all the new gold cadmium bling on my 64 Coupe de Ville "Dino" today…Continue

Blog Posts

1963 series 62 convertible transmission issue

Posted by Matthew VanDeWater on June 22, 2021 at 3:03pm 1 Comment

Hello I've been restoring a 63 for way to many years. Down to almost done, but have issue with trans linkage, when column in park shift rod 2 inches short. everything original. been trying to find picture of manual rod hooked up from under car to see position of linkage. was wondering if anybody has access for pictures. I wanted to see if my manual linkage is bent  wrong out of the trans if somebody dropped the trans or something. Doesn't make sense why it doesn't work. Thanks for any input…

Continue

New vehicle in the club

Posted by Patrick Westphal on June 17, 2021 at 4:00pm 1 Comment

I was successful in getting a vehicle from the New York contact I talked about at the last club meeting. I am still trying to figure out how to post a picture of the vehicle that is tied with this comment so if you see a random picture of a black convertible in a yard, that's me haha.  …

Continue

Torque converter grab when idling in Drive

Posted by Cliff Johnston on June 14, 2021 at 8:47pm 2 Comments

Hi Everyone, been quite a while since i have been on here.

I have had an issue with the idle on my 64 Coupe Deville ever since i have had it.

With the Idle set high enough that it is smooth, but still a nice idle, the RPM seems only slightly too high for the stall of the Torque Converter. And therefore it tends to sit there and grab and lunge a bit. So until now, i have been putting the car in Neutral at the lights to stop this happening.

I've had the car dyno tuned and…

Continue

Can you help? Driveshaft Question....

Posted by Chris on May 30, 2021 at 8:55am 1 Comment

Hello!

Newbie to the group here - we have already found tons of invaluable information on the board, so thanks! We are restoring a 1963 Series 62 Convertible. We are wondering if anyone knows of a source to buy the propellor yoke flange (that bolts to the pinion flange) for the driveshaft? One of our ears partially broke off. Not sure if we can buy just the yoke flange as an aftermarket part, or if it has to be rebuilt by a welder/fab guy? Maybe a salvage yard for a source? Again, any…

Continue

Videos

  • Add Videos
  • View All

© 2021   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service