HVAC Vacuum Valve Clip-need the one for the Power Control side

Hi.

Update:

I removed both 7 nipple vacuum valves and called my buddy who owns a machine shop. Tomorrow we'll re-surface the valve faces and then I'll reinstall them. HOWEVER, the one that comes out easily and comes apart with no rivet is on the Power module side. It installs on one side with a small bolt, and on the other it is held on by a clip, WHICH IS MISSING ON MY CAR. I am going to assume it is the same clip that is used on the Control Module side. Anybody got one? Happy to pay for it. 

Thanks

Norm 

Views: 759

Facebook Facebook

Comment

You need to be a member of 63/64 Cadillac Website to add comments!

Join 63/64 Cadillac Website

Comment by Norman Silverman on September 18, 2018 at 1:46am

I'm really stumped on where to tap the threads for the 4-40 screw and whether to try to do it in a way that holds the original arrangement with a rectangular clip that holds the rivet head on and provides tension between the halves. Has anybody done this repair? If yes, how?

Thanks

Comment by Norman Silverman on September 17, 2018 at 9:57pm

Noted. I want the machine shop guy to drill out the rivet and tap the old rivet head (large side) for the screw that will replace it. I intend to do the re-surfacing. The valve on the power piston side looks real good and has lubricant in it. I imagine it is still good, but I'll re-surface it anyway-a little bit. 

Thanks!

Photos

  • Add Photos
  • View All

Forum

The $120,000 1963 Eldorado on Bring a Trailer

Started by Jason Edge in General Discussion. Last reply by Kurt yesterday. 6 Replies

I have got a flood of email, texts, about the 63 Eldo that recently bid up to $120,000 and thought I would share for those that have not seen it.Here is the link:…Continue

Fuel Supply System - Check Points Beyond the Fuel Pump

Started by Jason Edge in General Discussion yesterday. 0 Replies

Incredibly, in 3 days I have had 3 people ask about replacing their fuel pump or even adding an electric fuel pump because there carb is not getting gas.  It has gotten to the point I have copied and…Continue

Tags: System, Delivery, Fuel

Front grill

Started by Phillip Hill in 1963/64 Cadillac Specific Discussion. Last reply by Dennis P. DiBari on Monday. 13 Replies

Hi everyone im currently restoring my my front grill due to some previous clown painting it with silver frost paint and doing a dodgy job I would like to know what parts of the grill are anodised.it…Continue

Houston we have a problem!

Started by Dave Fehrle in 1963/64 Cadillac Specific Discussion. Last reply by Jason Edge on Monday. 3 Replies

While enjoying the fruits of my labor on all new rear suspension and…Continue

Blog Posts

1963 RHS A/C kick panel - photos needed

Posted by SK on June 2, 2025 at 2:20pm 2 Comments

Could someone post front and back photos of the 1963 right-hand kick panel with A/C?

My car didn’t come with the original kick panels, so it's a bit of a mystery to me how I should cut the backing board and carpet to fit around the A/C.

Many thanks,

-Samu

Edelbrock Carb Block off Plates

Posted by Chase on March 12, 2025 at 2:05pm 14 Comments

Hey guys,

I have installed the same Edelbrock carb and have done everything the same as Jason’s carb and intake project. In the spring and summer months the car starts, runs and idles great! In the fall and winter months on a cold start, the car starts awful and wants to die until it warms up. I have to keep my foot on the throttle until it warms up or it will idle just terrible and try to die. Once it’s warm, it runs fantastic! Whats going on here? I was thinking of removing the…

Continue

'63 Tailfin Tales

Posted by Mark Mata on February 22, 2025 at 5:00pm 9 Comments

New old stock seat material

Posted by Ray Schick on August 22, 2024 at 6:25pm 2 Comments

I bought this seat material thinking that it’s…

Continue

Events

Videos

  • Add Videos
  • View All

© 2025   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service