Does anyone have a working ‘64 Convertible top switch like the one pictured below that you would be willing to sell, or have a lead on where I can get one?  The new so-called “replacement” switch doesn’t fit the panel hole correctly nor the original mounting bracket. (And it looks different than the original! 😁).

Mike

Facebook Facebook

Views: 55

Reply to This

Replies to This Discussion

…or know of a place that can rebuild my switch?

Have you tested the switch with a continuity tester to confirm it is not working, and that your problem is not in wiring or elsewhere? These are pretty simple switches with contacts that bend down and make contact and close circuit when switch button is pushed one way or the other. Sometimes contacts just need to be cleaned or bent a little. Send it to me and  would be glad to repair for free.. you would just pay for shipping it back.

Hi Jason,

Thank you for the reply and kind offer to repair my switch.  
iThe problem is the switch, which I have been gingerly using for the past couple of years.  With the dash restoration and having to remove the switch.  When putting back in and testing on the circuit, it sparked and upon removal for inspection, a pin came out along with a small piece of the plastic casing. (I had one of the ugly 3 pin “reproduction” to test the circuit and it works just fine, except the new switch is hanging out of the hole; a temporary thing to get the top up and down). If you think with the broken pin it is still reparable, I will send it to you.  Btw there is a broken clip on it.  
Thank you again for your advice and repair offer.

Mike

I have the base and clips from other switches and should be able to repair yours. Let's say $10 for replacement parts. If interested in me repairing send to 
Jason Edge
104 New Rand Rd
Garner, NC 27529
Note I will be shutting down around this Friday for my trip to  Gettysburg and the GN so if I get it say by Wednesday I should be able to get it shipped out before I leave. 

Thank you, Jason.

I’ll get it out to you tomorrow, overnight. 

Mike

Good Morning, Jason,

I shipped the switch today by UPS 2nd day.  You should receive it by Wednesday.   Thank you, again.

Mike

Mike, The switch was received today and has been repaired. Check your email.
Jason. 

You are amazing!   Thank you.

Mike.

RSS

Photos

  • Add Photos
  • View All

Forum

Front grill

Started by Phillip Hill in 1963/64 Cadillac Specific Discussion. Last reply by Dennis P. DiBari 2 hours ago. 8 Replies

Hi everyone im currently restoring my my front grill due to some previous clown painting it with silver frost paint and doing a dodgy job I would like to know what parts of the grill are anodised.it…Continue

Getting hot when going fast…

Started by Mack in 1963/64 Cadillac Specific Discussion. Last reply by Dennis P. DiBari 19 hours ago. 6 Replies

So… I do have a few of 63 Coupes, all have same setup with carbs, Pertronix, shroud, new US Radiator radiators etc … but only one of them gets a bit hot when I am hauling faster than 60mph and car…Continue

Rainstorm out of nowhere!

Started by Logan Robb in 1963/64 Cadillac Specific Discussion. Last reply by Dennis P. DiBari yesterday. 1 Reply

After dinner last night, we went for a quick cruise as the weather was cooler and the sun set was looking really good!Out of nowhere, a pop up shower appeared overhead and down-poured as we were…Continue

Convertible bumper jack

Started by Alan Clark in 1963/64 Cadillac Specific Discussion. Last reply by Logan Robb yesterday. 11 Replies

My car lacks the mechanism or spring needed to hold the jack in the storage slot on the right side of the trunk.  Anyone have a picture of the item I should find?Continue

Blog Posts

1963 RHS A/C kick panel - photos needed

Posted by SK on June 2, 2025 at 2:20pm 2 Comments

Could someone post front and back photos of the 1963 right-hand kick panel with A/C?

My car didn’t come with the original kick panels, so it's a bit of a mystery to me how I should cut the backing board and carpet to fit around the A/C.

Many thanks,

-Samu

Edelbrock Carb Block off Plates

Posted by Chase on March 12, 2025 at 2:05pm 14 Comments

Hey guys,

I have installed the same Edelbrock carb and have done everything the same as Jason’s carb and intake project. In the spring and summer months the car starts, runs and idles great! In the fall and winter months on a cold start, the car starts awful and wants to die until it warms up. I have to keep my foot on the throttle until it warms up or it will idle just terrible and try to die. Once it’s warm, it runs fantastic! Whats going on here? I was thinking of removing the…

Continue

'63 Tailfin Tales

Posted by Mark Mata on February 22, 2025 at 5:00pm 9 Comments

New old stock seat material

Posted by Ray Schick on August 22, 2024 at 6:25pm 2 Comments

I bought this seat material thinking that it’s…

Continue

Videos

  • Add Videos
  • View All

© 2025   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service