The dash clock was not working when I bought my '64 DeVille. I have now had a chance to go through much of the simple electrical issues and I am making headway. The clock did not run at all and it was a bit difficult to turn with the set knob. I removed the clock (Borg) and attempted to clean and oil it. The clock wire has power (as does the clock light wire (when headlights on)).
Upon "cleaning" the clock turned rather quickly with the set knob...maybe a bit too quickly. Upon my attempt to reinstall the clock and discovered I have caused a short in the clock, as when I touch the instrument bezel to seat the clock, the hands spin rather quickly and the clock light comes on without the headlights being on (and I blew the 25 amp fuse!!!!). I feel like a complete idiot.
In my over zealous effort to get the clock working and before I read a clock post here (which warns against using WD-40), I used WD-40......UGG!
Is my clock repairable, and if not, does anyone have one to sell, or a referral to where I might find one, or send it out for repair? Cosmetically the clock is in nice shape.
Thanks for all your help.
Mike
Tags:
Gentlemen,
After watching several YouTube videos on 50-70's classic car clock videos and studying how the clock actually worked with the points, I saw the problem. The escapement wheel gear was out of whack and thereby causing the points gear to open and close instantly (not "ticking"), flying back and forth to the points then to the stop and back. This caused the clock hands to spin rapidly as well and the fuse to burn out because the points had almost constant contact. I don't know about the bulb issue, but after reseating the escapement wheel (I hope it remains in place), and installing the clock with bulb before replacing the fuse, then replacing the fuse everything worked! Including the bulb only coming on when I turned on the headlights.
I stayed in the car for about 5 minutes and the clock seems to keep time pretty well. I'll know more in the morning. (Of course my wife is certain that I going to burn the house down!)
Mike
Started by Bill Wolf in 1963/64 Cadillac Specific Discussion. Last reply by Kurt yesterday. 1 Reply 0 Likes
My front door handle lights would not go on when I opened the doors. Bulbs were good and had power to them. Was not getting a ground. The door switch was corroded and wasn't making contact when the…Continue
Started by Bill Wolf in 1963/64 Cadillac Specific Discussion. Last reply by Bill Wolf on Saturday. 2 Replies 1 Like
I had to replace the heater core in my 63 SDV, so I decided to replace all the dash lights with LED's. and replaced all the vacuum lines. While I was in there, I added a light to the headlight switch…Continue
Started by Dave Fehrle in 1963/64 Cadillac Specific Discussion. Last reply by Robert Alan Shannon May 13. 9 Replies 0 Likes
I’m starting the complete rear suspension update/upgrade-new springs and shocks,replacing spherical joint and bushings on yoke and control links! Just wondering if there are any tips to help with the…Continue
Started by Mark Geertsma in 1963/64 Cadillac Specific Discussion. Last reply by Russ Austin May 12. 4 Replies 0 Likes
I’m struggling with my TV rod adjustment. I’ve been trying to adjust it as per shop manual, but it’s still not OK. When cold, it shifts smoothly through all four gears, when hot, it hesitates (lots…Continue
Tags: adjustment, rod, TV
Posted by Chase on March 12, 2025 at 2:05pm 14 Comments 1 Like
Hey guys,
I have installed the same Edelbrock carb and have done everything the same as Jason’s carb and intake project. In the spring and summer months the car starts, runs and idles great! In the fall and winter months on a cold start, the car starts awful and wants to die until it warms up. I have to keep my foot on the throttle until it warms up or it will idle just terrible and try to die. Once it’s warm, it runs fantastic! Whats going on here? I was thinking of removing the…
ContinuePosted by Ray Schick on August 22, 2024 at 6:25pm 2 Comments 0 Likes
I bought this seat material thinking that it’s…
Posted by Dave Fehrle on March 23, 2024 at 3:23pm 8 Comments 1 Like
While checking my Carter carb with engine running, I took the air cleaner off and there was a very loud hissing sound of air. I placed a piece of paper over the carb and it didn’t move up or down, is this normal?
© 2025 Created by Jason Edge.
Powered by