64 TH400 refresh
Next task with my 64 DeVille project is to check TH400 condition. Gearbox came with the car but was already removed. It is 64 but not possible to say if it is the original to this car as there is no VIN stamped like in later gearboxes. And again we have one-year-only part, so I hope no need to replace mechanical parts. I got 64 gasket kit already but probably will need some more rubber for inside parts.
Two bolts from extension housing were so corroded that they broke when opening, otherwise no damages yet. O-ring in filter was not properly in place, and was cut actually. Modulator is not holding vacuum so need to be replaced. Governor valve is stuck, I hope cleaning will solve that.
I will clean all parts and replace gaskets, and other parts if necessary. Oil was very clean and red inside but I think oil has been changed or added not long time ago.
I can see that 64 is slightly different from 79 which I repaired year ago. All hints and advice are highly appreciated. Shop Manual is in heavy use.
Replies to This Discussion
-
Permalink Reply by Mark S Anderson on
-
do i see some bits missing from the big band top left?
-
Permalink Reply by Matti Roth on
-
I did not notice that but will check! Thanks Mark.
-
-
Rear band is ok, I took closer look.
-
-
I opened governor, cleaned the valve and it started to move like it should.
It seems that control valve assy gaskets for 64 are difficult to find. Need to search more. Luckily I got gaskets out in good condition so I can use the old ones if new ones not available.
-
Permalink Reply by Tony and Ginny 429 on
-
Fatsco could have the trans parts you may be needing
Enjoy
-
-
Matti
Any detail explanation and photos ( with circles and arrows ) you may be able to offer on the trans repair you are doing will be helpful for those seeing the inside of a turbo trans on this web site for the first time — I am on this site daily since 2006
Thank you in advance for any info you can share with our community regarding the trans repair you are now performing
Enjoy
-
Permalink Reply by Anders on
-
Matti, I know you bought parts from TA Motor before and they might have what you are looking for now.
However I have bought gear box parts from MrMechanic. He had stuff that no other had. So try him.
When TA doesn't have the parts they recommend BA Motors for used parts, but usually BA don't post the stuff on the website. Call or email them is a better bet.
There is also a chance American Cars scrapyard in Osby might have something, maybe not for the gear box but for other parts.
Finally, Hortlund could very well be your savior. I got tires for my -87 Buick and -64 Cadillac from him.
-
-
Big thanks, Anders! Looks like I will get all I need from Björn in MrMechanic.
Tack så mycket!
-
-
Valve body is easy to check and clean with help from Shop manual. Dismantling, cleaning, checking, assembly with atf oil. One dirt accumulation was found inside 1-2 shift valve.
I use ultrasound washer for cleaning metal parts.
-
-
Testing detent solenoid with 12V power.
-
-
Oil pump gets new bushings and seals
-
-
Matti
Your skills rebuilding the turbo trans are extremely impressive to me and I am enjoy every minute you are posting to learn what I might
I was good at rebuilding my 4 speed trans behind my Super stock 1/8 mile race car when required but nothing compared to what you are doing here
Do tell me a little about your back ground to be taking this task on as you have
Enjoy
Photos
Members
Forum
1964 A/C Delco Parts book for Deville
Started by Mark Bartlett in General Discussion 3 hours ago. 0 Replies 0 Likes
Is there a place to go to buy or look at original parts book ThanksssContinue
differential seal
Started by Al zink in 1963/64 Cadillac Specific Discussion. Last reply by Al zink 12 hours ago. 2 Replies 0 Likes
Can anyone provide me with a good source for a differential seal for my 63 cadillacThanksContinue
1964 turbo trans
Started by JOHN V SCHILLACI in General Discussion. Last reply by Tony and Ginny 429 yesterday. 1 Reply 0 Likes
Hello, Does anyone know if the spacer between the engine and turbo trans year specific? If not what years fit which.Continue
Tires
Started by Mark Bartlett in 1963/64 Cadillac Specific Discussion. Last reply by Mark Bartlett yesterday. 26 Replies 0 Likes
Hi I am new to this Discussion I currently purchasing a 64 Deville convertible and It has bias ply tires that are 15 year old they have L-78-15 tires and would like to put on radials . Question …Continue
Blog Posts
Lower Front End Ball Joints
Posted by Logan Robb on May 11, 2023 at 9:04am 7 Comments 0 Likes
Good Morning all!
I took the 64 into the shop to have some adjustments completed and in the process decided to have the lower ball joints replaced as was recommended the last time I had it in. I ordered the parts and came into the shop. They quoted me nearly $500 to replace those lower ball joints requiring nearly 4hrs of labor. Now this is a reputable shop and they know me by name here and they will continue to get my business. I am just questioning what on earth is…
Continue1964 power steering sector rebuild
Posted by CHRIS CARLSON on March 20, 2023 at 11:32pm 3 Comments 0 Likes
I'm having my steering sector rebuilt, and considering changing it from 20-1 ratio 4.2 turns lock to lock to 3.5 turns lock to lock @ 16-1 ratio, If i change from a 3 1/4" box to a 3" box i could have a 14-1 Ratio steering response would be faster, shorter distance to turn the wheel to get a response, has anyone done this? and how do you like it? thank you
1964 Daville dashboard clock
Posted by Willem Bol on March 13, 2023 at 11:33am 2 Comments 0 Likes
Hallo,
Can somebody help me finding a dashboard clock for my 1964 Cadillac DeVille Convertible?
Thank you in advance,
Willem Bol
The Netherlands
Does anyone know where I can get the bushings for AC compressor mount on the 429?
Posted by Robert Schles on February 21, 2023 at 11:45am 2 Comments 0 Likes
I've looked at the usual rubber sources but couldn't find any.
Events
© 2023 Created by Jason Edge.
Powered by
