Anybody out there have any experience or direction how to remove and replace the chrome trim moulding around the front door window glass? Kevin
Tags:
Kevin, the window has t come out. If its a 63, lucky U. 2 screws hold the bar in place. The rollers on the regulator ride in the bar, on the bottom of the window channel
2 screws on the back of the top chrome L shaped piece, hold it to the channel.
I got it replaced. Thanks Russ. Kevin
Kevin, is your window already out of the car? If not follow shop manual to remove glass. Then remove screws that hold the side & top trim to the lower channel assembly and gently pry the trim away from glass. When reinstalling I have used a lot of WD 40 to get the window back wedged into the seal and trim and lower channel.
Thanks Jason. It worked!!!! Got it. Kevin
so u have to take the front window out in order to remove front window trim??? im in process of trying to remove trim or trying figure it out .but dont wanna take that Big window out
Looking at picture below for front window trim with read arrows pointing to left and right roof panel trim, and green arrows pointing to 5 pc reveal trim:
--> left, top and right reveal trim next to glass (green arrows) - removes with reveal removal tool. (windshield does not have to be removed)
--> bottom left and right reveal trim behind cowl (bottom green arrows) - cowl has tom come off to access 5/16" screws that hold lower reveal brackets in place. (windshield does not have to be removed)
--> left and right front roof panel trim (red arrows) - WINDSHIELD AS TO COME UP TO ACCESS TRIM SCREWS). The removal of this trim indicating removal of windshield is in the Shop manual (page 16-80 in 1963 manual; page 16-85 1964 manual),
Once you remove the windshield and rubber seal you will then have access to a series of screws that holds the left and right front roof panel trim in place as seen below:
Started by Jason Edge in 1963/64 Cadillac Specific Discussion. Last reply by Dave Fehrle 2 hours ago. 1 Reply 1 Like
Had my double surgery on left arm March 4 on wrist and elbow to address Cubital Tunnel Syndrome and so far so good. Basically the open me up at these two locations and move the Ulner nerve around to…Continue
Started by Mark Mata in 1963/64 Cadillac Specific Discussion. Last reply by Mark Mata on Sunday. 5 Replies 0 Likes
Hello Chapter, I had a question on the mounting holes for the front…Continue
Started by Jason Edge in Newsletters. Last reply by Matti Roth Mar 3. 2 Replies 0 Likes
I have just completed and posted the March 2025, 1963/64 Cadillac Chapter Newsletter to our…Continue
Started by Jason Edge in General Discussion. Last reply by Jason Edge Mar 3. 6 Replies 1 Like
I have made some "factory" upgrades to my 64 Coupe de Ville by installing some options available to my Coupe de Ville such as power vent windows, tilt steering column, am/fm, 3 way rearview mirror,…Continue
Posted by Chase on March 12, 2025 at 2:05pm 1 Comment 0 Likes
Hey guys,
I have installed the same Edelbrock carb and have done everything the same as Jason’s carb and intake project. In the spring and summer months the car starts, runs and idles great! In the fall and winter months on a cold start, the car starts awful and wants to die until it warms up. I have to keep my foot on the throttle until it warms up or it will idle just terrible and try to die. Once it’s warm, it runs fantastic! Whats going on here? I was thinking of removing the…
ContinuePosted by Ray Schick on August 22, 2024 at 6:25pm 2 Comments 0 Likes
I bought this seat material thinking that it’s…
Posted by Dave Fehrle on March 23, 2024 at 3:23pm 8 Comments 1 Like
While checking my Carter carb with engine running, I took the air cleaner off and there was a very loud hissing sound of air. I placed a piece of paper over the carb and it didn’t move up or down, is this normal?
© 2025 Created by Jason Edge.
Powered by